Dzisiaj jest 29 wrz 2020, 13:30

Strefa czasowa UTC+1godz. [letni]




Nowy temat Odpowiedz w temacie  [ Posty: 45 ]  Przejdź na stronę Poprzednia  1, 2, 3
Autor Wiadomość
 Tytuł: Re: Jak używać cfetool przy Broadcomie (komenda dump memory)
Post: 31 sie 2020, 19:59 
Offline
Użytkownik

Rejestracja: 2 sty 2016, 11:28
Posty: 62
Czyli to może być, np. ukryte?
drwxr-xr-x 11 xxxx xxxx 4096 cze 6 2017 ./
drwxrwxrwx 15 xxxx xxxx 4096 cze 6 2017 ../
Raczej nic sam nie ukrywałem. Myślałem, że domyślnie jak w Windowsie może być aktywne.
Masz jakiś pomysł jak się do tego var/passwd dostać?
Posiadam trzy zrzuty do .bin.
Jak czytam to często przewija się coś takiego jak emulacja w Qemu.
Warte to uwagi? Czy jest coś znacznie prostszego?


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: Jak używać cfetool przy Broadcomie (komenda dump memory)
Post: 31 sie 2020, 20:02 
Offline
Administrator
Awatar użytkownika

Rejestracja: 10 kwie 2010, 00:28
Posty: 13757
Lokalizacja: Warszawa
Generalnie nie dasz rady uruchomić takiego gotowego obrazu na emulatorze.

Pik nie jest ukryty. Jest albo generowany albo odczytywany z nvram czy czegoś podobnego.

_________________
http://eko.one.pl - prawie wszystko o OpenWrt


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: Jak używać cfetool przy Broadcomie (komenda dump memory)
Post: 31 sie 2020, 21:16 
Offline
Użytkownik

Rejestracja: 2 sty 2016, 11:28
Posty: 62
Tutaj jeden z użytkowników ma trzy obszary:
https://forum.archive.openwrt.org/viewt ... p?id=46498
U mnie jest tylko jakby ten mtdblock0. Czy jest możliwe, że reszta znajduje się na innej kości? FW jest podobne, bo to ten sam operator w każdym przypadku.
Czy pełny log z uruchomienia (serial) by coś tu wniósł? Widać tam będzie co i skąd się zaczytuje?
Dump zrobiłem tym sposobem: https://forum.archive.openwrt.org/viewt ... p?id=30554
Wypakowuję używając komendy binwalk --extract --quiet flash.bin


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: Jak używać cfetool przy Broadcomie (komenda dump memory)
Post: 31 sie 2020, 21:41 
Offline
Administrator
Awatar użytkownika

Rejestracja: 10 kwie 2010, 00:28
Posty: 13757
Lokalizacja: Warszawa
Czy widać to sprawdź, ale pewnie nie, bo nie ma potrzeby żeby takie informacje wypisywać na konsoli. Choć logi po serialu powinieneś od razu od razu zrobić, bo tam wiele innych ciekawy rzeczy może pisać.

_________________
http://eko.one.pl - prawie wszystko o OpenWrt


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: Jak używać cfetool przy Broadcomie (komenda dump memory)
Post: 14 wrz 2020, 09:37 
Offline
Użytkownik

Rejestracja: 2 sty 2016, 11:28
Posty: 62
3225:


CFE version 1.0.37-110.4-2 for BCM96368 (32bit,SP,BE)
Build Date: Thu Feb 20 14:32:25 CST 2014 (herbert@rd7-server)
Copyright (C) 2000-2009 Broadcom Corporation.

Parallel flash device: name MX29GL128EH, id 0x2221 size 16384KB
Total Flash size: 16384K with 128 sectors
Chip ID: BCM6368B2, MIPS: 400MHz
Main Thread: TP0
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000

Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id (0-15)                   : 96368IT-1441N1
Number of MAC Addresses (1-32)    : 32
Base MAC Address                  : d8:b6:b7:90:f7:bf
PSI Size (1-64) KBytes            : 24
Enable Backup PSI [0|1]           : 1
System Log Size (0-256) KBytes    : 0
Main Thread Number [0|1]          : 0
Serial Number                     : 158QOA01488
Voice Board Configuration (0-0)   : ADVNgr_3225u

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xb8020000) ...
Code Address: 0x80010000, Entry Address: 0x802eaea0
Decompression OK!
Entry at 0x802eaea0
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x802eaea0
Linux version 2.6.30 (yanyang@localhost.localdomain) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #2 Tue Jun 6 19:19:34 CST 2017
Parallel flash device: name MX29GL128EH, id 0x2221 size 16384KB
96368IT-1441N1 prom init
Linux TP ID = 0
CPU revision is: 0002a031 (Broadcom4350)
Determined physical RAM map:
 memory: 03ece000 @ 00000000 (usable)
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  Normal   0x00001000 -> 0x00003ece
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00003ece
On node 0 totalpages: 16078
free_area_init_node: node 0, pgdat 80387bd0, node_mem_map 81000000
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 94 pages used for memmap
  Normal zone: 11888 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 15952
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
NR_IRQS:128
PID hash table entries: 256 (order: 8, 1024 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Allocating memory for DSP module core and initialization code
Allocated DSP module memory - CORE=0x8108c720 SIZE=1590816, INIT=0x81210d40 SIZE=44
Memory: 58176k/64312k available (2948k kernel code, 6116k reserved, 609k data, 132k init, 0k highmem)
Calibrating delay loop... 399.36 BogoMIPS (lpj=199680)
Mount-cache hash table entries: 512
--Kernel Config--
  SMP=0
  PREEMPT=0
  DEBUG_SPINLOCK=0
  DEBUG_MUTEXES=0
Broadcom Logger v0.1 Jun  6 2017 19:15:28
net_namespace: 1100 bytes
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:01.0: reg 10 32bit mmio: [0x000000-0x00ffff]
pci 0000:00:09.0: reg 10 32bit mmio: [0x10001600-0x100016ff]
pci 0000:00:0a.0: reg 10 32bit mmio: [0x10001500-0x100015ff]
BLOG v3.0 Initialized
BLOG Rule v1.0 Initialized
Broadcom IQoS v0.1 Jun  6 2017 19:18:33 initialized
Broadcom GBPM v0.1 Jun  6 2017 19:18:33 initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
fuse init (API version 7.11)
msgmni has been set to 113
io scheduler noop registered (default)
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
bcm963xx_mtd driver v1.0
File system address: 0xb8020100
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 15, io mem 0x10001500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 13, io mem 0x10001600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x8017 is enabled
Serial: BCM63XX driver $Revision: 3.00 $
Magic SysRq enabled (type ^ h for list of supported commands)
ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX
Total # RxBds=2960
bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized

bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.3 Jun  6 2017 19:18:16
IPSEC SPU: SUCCEEDED
GACT probability NOT on
Mirror/redirect action on
u32 classifier
    input device check on
    Actions configured
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
Bridge firewalling registered
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing unused kernel memory: 132k freed
init started:  BusyBox v1.00 (2017.06.06-11:21+0000) multi-call binary


BusyBox v1.00 (2017.06.06-11:21+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.


Loading drivers and kernel modules...

ct_hotplug_monitor: not found
208
bcm_ingqos: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Broadcom Ingress QoS Module  Char Driver v0.1 Jun  6 2017 19:17:04 Registered<243>

Broadcom Ingress QoS ver 0.1 initialized
BPM: tot_mem_size=67108864B (64MB), buf_mem_size=10066329B (9MB), num of buffers=4802, buf size=2096
Broadcom BPM Module Char Driver v0.1 Jun  6 2017 19:16:03 Registered<244>
[NTC bpm] bpm_set_status: BPM status : enabled

Initialized fcache state
Broadcom Packet Flow Cache  Char Driver v2.2 Jun  6 2017 19:17:09 Registered<242>
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
Constructed Broadcom Packet Flow Cache v2.2 Jun  6 2017 19:17:09
CMF:CONFIG cmfConstruct:
CMF:CONFIG pktDbgLvl[0xc00dd9e4]=0
CMF:HAL pktCmfHalConstruct:
CMF:HAL pktDbgLvl[0xc00d569c]=0
CMF:HAL pktCmfHalConstruct:
CMF:HAL pktDbgLvl[0xc00d569c]=0
CMF:DRV pktCmfDrvConstruct:
CMF:DRV pktDbgLvl[0xc00dd9f4]=0
Broadcom Packet CMF (Experimental) Char Driver v0.1 Jun  6 2017 19:17:08 Registered<232>
CMF:PROTO pktCmfProtoConstruct:
CMF:PROTO pktDbgLvl[0xc00dd9c0]=0
Broadcom Packet CMF (Experimental) [6368-B2] v0.1 Jun  6 2017 19:17:08 Loaded
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM6368B2 Ethernet Network Device v0.1 Jun  6 2017 19:18:11
ETH Init: Ch:0 - 180 tx BDs at 0xa3950000
ETH Init: Ch:0 - 960 rx BDs at 0xa3008000
######## ethsw_init_table:105 ####### switch_port_phyid[0]=1
######## ethsw_init_table:105 ####### switch_port_phyid[1]=2
######## ethsw_init_table:105 ####### switch_port_phyid[2]=3
######## ethsw_init_table:105 ####### switch_port_phyid[3]=4
######## ethsw_init_table:105 ####### switch_port_phyid[4]=17
/proc/buffer16 created
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
CMF:HW pktDbgLvl[0xc00ce640]=0
CMF:HW pktCmfHwReset: Reset HW layer.
Broadcom Packet CMF (Experimental) SWC RESET.
BRCM Ext Switch: Tag <0:0x0:0> Port<0>
Broadcom Packet CMF (Experimental) SWC INITIALIZED.
CMF:FWD pktCmfFwdDevConstruct:
CMF:FWD pktDbgLvl[0xc00ddc64]=0
Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Jun  6 2017 19:17:08 Registered
CMF Fwd Hnd DbgLvl <0xc00ddc90> = <0>
CMF:FWD pktCmfFwdDevConstruct:
CMF:FWD pktDbgLvl[0xc00ddc64]=0
Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Jun  6 2017 19:17:08 Registered
CMF Fwd Hnd DbgLvl <0xc00ddc90> = <0>
Broadcom Packet CMF (Experimental) ENABLED.
===== Found Interface name mapping : 96368IT-1441N1 =====
eth1: MAC Address: D8:B6:B7:90:F7:BF
eth2: MAC Address: D8:B6:B7:90:F7:BF
eth3: MAC Address: D8:B6:B7:90:F7:BF
eth4: MAC Address: D8:B6:B7:90:F7:BF
eth0: MAC Address: D8:B6:B7:90:F7:BF
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:01.0 to 64
wl: passivemode=1
wl: napimode=0
wl: allocskbmode=1
wl:srom strapped
wl:(srom strapped) probe/present=0
wl:srom not detected, using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm43222_map.bin
wl0: Broadcom BCMa8d6 802.11 Wireless Controller 5.100.123.0.cpe4.10L02.6
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
IRQ 21/brcm_21: IRQF_DISABLED is not guaranteed on shared IRQs
DSP Driver: DSP init stub
Endpoint: endpoint_init entry
Endpoint: endpoint_init COMPLETED
p8021ag: p8021ag_init entry
Broadcom 802.1Q VLAN Interface, v0.1
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
usbcore: registered new interface driver cdc_acm
cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
usbcore: registered new interface driver hso
hso: 1.6-Option:USB High Speed Option driver

===== Comtrend Release Version W631-S410TPS-C04_R12 =====

-- Delete 0 WANDelegated Prefix -BOS: Enter bosInit
-
-- Delete 0 LBOS: Exit bosInit
oopback static rendpoint_open COMPLETED
oute --
ssk:debug:16.453:lck_checkBeforeEntry:171:lock required during cmsObj_getNextInSubTreeFlags
ip_tables: (C) 2000-2006 Netfilter Core Team
/proc/PSD_data created
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (2500 buckets, 10000 max)
ctnetlink v0.93: registering with nfnetlink.
ip6_tables: (C) 2000-2006 Netfilter Core Team
sendto: Network is unreachable
device eth1 entered promiscuous mode
######## bcm63xx_enet_open:1348 ####### dev->base_addr=0 phyport:0 0
ADDRCONF(NETDEV_UP): eth1: link is not ready
device eth2 entered promiscuous mode
######## bcm63xx_enet_open:1348 ####### dev->base_addr=1 phyport:0 1
ADDRCONF(NETDEV_UP): eth2: link is not ready
device eth3 entered promiscuous mode
######## bcm63xx_enet_open:1348 ####### dev->base_addr=2 phyport:1 2
ADDRCONF(NETDEV_UP): eth3: link is not ready
device eth4 entered promiscuous mode
######## bcm63xx_enet_open:1348 ####### dev->base_addr=3 phyport:2 3
ADDRCONF(NETDEV_UP): eth4: link is not ready
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
BcmAdsl_Initialize=0xC016CF38, g_pFnNotifyCallback=0xC019FDF4
kerSysGetSerialNumber: sn is 158QOA01488
Clocks for QPROC and AFE are being aligned with step through ...
AFE is aligned, i = 063, PhaseValue = -050, PhaseCntl = 0x3FC10000
QPROC is aligned, i = 064, PhaseValue = -050, PhaseCntl = 0x3FC13FC0
Clocks for QPROC and AFE are aligned with syn_status AFE = 0x70, QPROC = 0x70
AFE  phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f
QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f
WLmngr Daemon is running
optarg=0 shmId=0
pSdramPHY=0xA3FFFFF8, 0xE2B7C7B2 0xF397F2F9
*** XfaceOffset: 0x5FF90 => 0x5FF90 ***
wlevt is ready for new msg...
*** PhySdramSize got adjusted: 0xD8C2C => 0x10F350 ***
AdslCoreSharedMemInit: shareMemSize=142477(142480)
AdslCoreHwReset:  pLocSbSta=81610000 bkupThreshold=3072
AdslCoreHwReset:  AdslOemDataAddr = 0xA3F9B184
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
XTM Init: 512 rx BDs at 0xa1618000
XTM Init: 16 rx BDs at 0xa1fb0c80
Register interface pppoa0 !!
Register interface pppoa3 !!
Register interface ppp1.1 !!
Register interface ppp4.2 !!
######## bcm63xx_enet_open:1348 ####### dev->base_addr=5 phyport:5 5
####reset_IP1001:512 #### IP1001 Reset OK !! phyAddr=0x11
####reset_IP1001:549 ####  IC+ control reg09 =0x1700
ADDRCONF(NETDEV_UP): eth0: link is not ready
Register interface ppp2.1 !!
Could not get lock!
group[0] = 0x1df
Success
Success
Success
Success
monitor task is initialized pid= 312

isEthObjectOnBr0_1:568 ####### lanIpIntfObj->X_BROADCOM_COM_IfName=br0:1 ,found = 1 ################

isEthObjectOnBr0_1:570 ####### orig lanIpIntfObj->enable =1 ################

isEthObjectOnBr0_1:572 ####### force enable lanIpIntfObj->enable =1 ################

initVodslBoundIpIfLanSideUpLocked:380 ######### LAN use TPSA Virtual Interface, br0ipAddr =172.28.130.173 ################
ssk:debug:50.447:initialFirewall:832:Enter.
br0: port 5(wl0) entering disabled state
There is no Predefined DevicePin in CFE
WPS Device PIN = 16333338
Could not get lock!
Setting SSID: "NFGostynin"
Setting SSID: "wl0_Guest1"
Setting SSID: "wl0_Guest2"
Setting SSID: "wl0_Guest3"
Switch MDK: num_switches = 1
Switch MDK: unit = 0; phy_pbmp = 0x2f; config_pbmp = 0x2f
Switch MDK link poll thread: unit=0; phypbmp=0x2f
##### ethsw_IP1001_init:8076 #####
####reset_IP1001:512 #### IP1001 Reset OK !! phyAddr=0x11
####reset_IP1001:549 ####  IC+ control reg09 =0x1700
Comtrend_Polling:debug:58.887:initLoggingFromConfig:221:failed to get lock, ret=9809

UPnP daemon is ready to run
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
BOS: Enter bosInit
acsd: scan in progress ...
00:01:09 vodslCmsMutexLockInit: Created MDM Mutex
bosTimerInit
Enter bosAppInit Exit bosAppInit BOS: Exit bosInit
vrgEndptDriverOpen: Endpoint driver open success
vrgEndptDriverOpen: Endpoint driver open success
Sorry, rule does not exist.
Sorry, rule does not exist.
Sorry, rule does not exist.
vodsl:debug:69.275:setVodslSipQosRule:351:maxRtpPortNum = 32456, minRtpPortNum = 22456

acsd: scan in progress ...
acsd: selected channel spec: 0x2b01
[DBG xdrv_slic] slicLe89116Init: (ts: 10s 784ms):SLIC: Starting 89116 device and line initializion...
[DBG xdrv_slic] deviceReset: (ts: 10s 809ms):SLIC: Reset applied on GPIO pin 10
[DBG xdrv_slic] slicLe89116Init: (ts: 10s 822ms):89116: Configured for BUCKBOOST_100V
[DBG xdrv_slic] initZarlinkDevice: (ts: 10s 830ms):SLIC: Initializing Zarlink device 0
[DBG xdrv_slic] zarlinkProcessEvents: (ts: 10s 858ms):SLIC: Received VP_DEV_EVID_DEV_INIT_CMP event
[DBG xdrv_slic] zarlinkWaitForEvent: (ts: 10s 868ms):SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 1024 i=0
[DBG xdrv_slic] initZarlinkDevice: (ts: 10s 880ms):SLIC: Zarlink device 0 initialized OK
[DBG xdrv_slic] initZarlinkLines: (ts: 10s 890ms):SLIC: Zarlink Locale set to 25
[DBG xdrv_slic] initZarlinkLines: (ts: 10s 898ms):SLIC: Initializing Zarlink FXS line 0
[DBG xdrv_slic] slicGetRingLocale: (ts: 10s 907ms):******DeviceInfo PRODUCT CODE: 0
[DBG xdrv_slic] zarlinkProcessEvents: (ts: 10s 930ms):SLIC: Received VP_LINE_EVID_LINE_INIT_CMP event
[DBG xdrv_slic] zarlinkWaitForEvent: (ts: 10s 940ms):SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 2048 i=0
br0: port 5(wl0) entering forwarding state
Could not get lock!
[DBG xdrv_slic] zarlinkProcessEvents: (ts: 13s 251ms):SLIC: Received VP_EVID_CAL_CMP event
[DBG xdrv_slic] zarlinkWaitForEvent: (ts: 13s 260ms):SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 64 i=216
[DBG xdrv_slic] initZarlinkLines: (ts: 13s 272ms):SLIC: FXS line 0 RX timeslot = 0
[DBG xdrv_slic] initZarlinkLines: (ts: 13s 281ms):SLIC: FXS line 0 TX timeslot = 0
[DBG xdrv_slic] initZarlinkLines: (ts: 13s 290ms):SLIC: Zarlink FXS line 0 initialized OK
[DBG xdrv_slic] slicLe89116Init: (ts: 13s 299ms):SLIC: 89116 device 0 and FXS/FXO initializion COMPLETED OK !
[DBG xdrv_slic] slicLe89316Init: (ts: 13s 326ms):SLICDAA: Starting 89316 device and line initializion...
[DBG xdrv_slic] slicLe89316Init: (ts: 13s 336ms):SLICDAA: Skipping SLIC chip reset
[DBG xdrv_slic] slicLe89316Init: (ts: 13s 345ms):89316: Configured for BUCKBOOST_100V
[DBG xdrv_slic] initZarlinkDevice: (ts: 13s 354ms):SLIC: Initializing Zarlink device 0
[DBG xdrv_slic] zarlinkProcessEvents: (ts: 13s 381ms):SLIC: Received VP_DEV_EVID_DEV_INIT_CMP event
[DBG xdrv_slic] zarlinkWaitForEvent: (ts: 13s 391ms):SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 1024 i=0
[DBG xdrv_slic] initZarlinkDevice: (ts: 13s 403ms):SLIC: Zarlink device 0 initialized OK
[DBG xdrv_slic] initZarlinkLines: (ts: 13s 413ms):SLIC: Zarlink Locale set to 25
[DBG xdrv_slic] initZarlinkLines: (ts: 13s 421ms):SLIC: Initializing Zarlink FXS line 0
[DBG xdrv_slic] slicGetRingLocale: (ts: 13s 430ms):******DeviceInfo PRODUCT CODE: 0
[DBG xdrv_slic] zarlinkProcessEvents: (ts: 13s 452ms):SLIC: Received VP_LINE_EVID_LINE_INIT_CMP event
[DBG xdrv_slic] zarlinkWaitForEvent: (ts: 13s 463ms):SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 2048 i=0
[DBG xdrv_slic] zarlinkProcessEvents: (ts: 15s 825ms):SLIC: Received VP_EVID_CAL_CMP event
[DBG xdrv_slic] zarlinkWaitForEvent: (ts: 15s 834ms):SLIC: Found event: pEvent.eventCategory = 2 pEvent.eventId = 64 i=235
[DBG xdrv_slic] initZarlinkLines: (ts: 15s 846ms):SLIC: FXS line 0 RX timeslot = 2
[DBG xdrv_slic] initZarlinkLines: (ts: 15s 855ms):SLIC: FXS line 0 TX timeslot = 2
[DBG xdrv_slic] initZarlinkLines: (ts: 15s 864ms):SLIC: Zarlink FXS line 0 initialized OK
[DBG xdrv_slic] initZarlinkLines: (ts: 15s 873ms):SLIC: Initializing Zarlink FXO line
[DBG xdrv_slic] daaGetLocale: (ts: 15s 882ms):SLIC: daaGetLocale 25
[DBG xdrv_slic] daaGetDialLocale: (ts: 15s 889ms):SLIC: daaGetDialLocale 25
[ERROR xdrv_slic] initZarlinkLines,480: (ts: 15s 897ms):SLIC: VpInitLine failed (3)
[ERROR xdrv_slic] initZarlinkLines,486: (ts: 20s 906ms):DAA: ERROR: Line initialization was not completed
[ERROR xdrv_slic] slicLe89316Init,202: (ts: 20s 916ms):SLICDAA: 89316 FXS/FXO line initializion FAILED !.
[ERROR ept] boardHalSlicInit,459: (ts: 20s 927ms):ERROR during 89316 SLIC initialization!!!
boardHalInit completed
******* DSP: Found BCM96368 *******
gDectRxOutOfSyncCounter = 0x8114c224
gDectTxOutOfSyncCounter = 0x8114c228
gApmAssertEnabled    = 0x8115F030
gPcmAssertEnabled    = 0x8115F02C
gInterruptCounter    = 0x8114C250
gInterruptErrors     = 0x8114C254
gPcmRxDescRing.next       = 0x8115F06C
gPcmTxDescRing.next       = 0x8115F064
gApmRxDescRing[0].ext   = 0x8115F04C
gApmTxDescRing[0].next   = 0x8115F03C
gApmRxDescRing[1].ext   = 0x8115F054
gApmTxDescRing[1].next   = 0x8115F044
32 ms ECAN tail-length
halPcmInitDescriptors 144 nextTxDesc = 0xA0C94000
halPcmInitDescriptors 144 nextTxDesc = 0xA0C94008
halPcmInitDescriptors 148 Ownership for TX desc not set. Use this buffer.
DSP: Interrupt Masks
---------------
IrqMask                   = 0x00000707
IrqMask1                  = 0x40000000

DSP: Interrupt Status
-----------------
IrqStatus                 = 0x00000000
IrqStatus1                = 0x00000000
EndpointInit completed
dgasp: kerSysRegisterDyingGaspHandler: endpoint registered
[DBG xdrv_slic] slicZarlinkModeControl: (ts: 21s 922ms):SLIC: Mode for FXS channel changed to 1
[DBG xdrv_slic] slicZarlinkModeControl: (ts: 21s 941ms):SLIC: Mode for FXS channel changed to 1
[DBG xdrv_slic] slicZarlinkModeControl: (ts: 22s 51 ms):SLIC: Mode for FXS channel changed to 1
returned by bosTimeSetWallTime: No such file or directory (2)Enter TaskCreate VRGCMGRTaskCreate - spawn new task VRGCMGRExit TaskCreate
######## cmCallConfig:480 parm.protcfg.ext.prackPref = 2 #########

### Register Mode ID10 Enable : 1 ###

### Register Mode ID10 Enable : 1 ###

cmEndpt: 1, cid -1: CMEVT_INSERVICE in CMST_ONHOOK endpt state
######################cmSetCfgCodec:2504##################maxUsedCodecNum = 2
######################cmSetCfgCodec:2504##################maxUsedCodecNum = 6

cmNatKeepAliveInit:1527 ################# cmNatKeepAliveInterMs_TPSA[0]=0  ##############

cmNatKeepAliveInit:1528 ################# cmNatKeepAliveInterMs_TPSA[1]=0  ##############
00:01:22 Couldn't get provisioning value

00:01:22 Couldn't get provisioning value

[DBG xdrv_slic] slicZarlinkModeControl: (ts: 22s 289ms):SLIC: Mode for FXS channel changed to 1

cmEndpt: 0, cid -1: CMEVT_INSERVICE in CMST_ONHOOK endpt state

cmEndpt: 1, cid -1: CMEVT_INSERVICE in CMST_ONHOOK endpt state

## cmUpdateTPSAExtReg:4905 endpt cmEndpt[0].inservice=0 ##
## cmUpdateTPSAExtReg:4906 i     cmEndpt[1].inservice=0 ##
#### cmProcessCallEvent:430 cmEndpt[0].regRetryTimerMs = 60000 ###
00:01:22 unknown msg: dataLength=0 msg type=268437506

cmEndpt: 0, cid -1: CMEVT_INSERVICE in CMST_ONHOOK endpt state

cmEndpt: 1, cid -1: CMEVT_INSERVICE in CMST_ONHOOK endpt state

## cmUpdateTPSAExtReg:4905 endpt cmEndpt[0].inservice=0 ##
## cmUpdateTPSAExtReg:4906 i     cmEndpt[1].inservice=0 ##
#### cmProcessCallEvent:430 cmEndpt[0].regRetryTimerMs = 60000 ###

cmEndpt: 0, cid -1: CMEVT_INSERVICE in CMST_ONHOOK endpt state

cmEndpt: 1, cid -1: CMEVT_INSERVICE in CMST_ONHOOK endpt state

## cmUpdateTPSAExtReg:4905 endpt cmEndpt[0].inservice=0 ##
## cmUpdateTPSAExtReg:4906 i     cmEndpt[1].inservice=0 ##
#### cmProcessCallEvent:430 cmEndpt[0].regRetryTimerMs = 60000 ###

cmEndpt: 0, cid -1: CMEVT_INSERVICE in CMST_ONHOOK endpt state

cmEndpt: 1, cid -1: CMEVT_INSERVICE in CMST_ONHOOK endpt state

## cmUpdateTPSAExtReg:4905 endpt cmEndpt[0].inservice=0 ##
## cmUpdateTPSAExtReg:4906 i     cmEndpt[1].inservice=0 ##
#### cmProcessCallEvent:430 cmEndpt[0].regRetryTimerMs = 60000 ###

cmEndpt: 0, cid -1: CMEVT_INSERVICE in CMST_ONHOOK endpt state

cmEndpt: 1, cid -1: CMEVT_INSERVICE in CMST_ONHOOK endpt state

## cmUpdateTPSAExtReg:4905 endpt cmEndpt[0].inservice=0 ##
## cmUpdateTPSAExtReg:4906 i     cmEndpt[1].inservice=0 ##
#### cmProcessCallEvent:430 cmEndpt[0].regRetryTimerMs = 60000 ###

cmEndpt: 0, cid -1: CMEVT_INSERVICE in CMST_ONHOOK endpt state

cmEndpt: 1, cid -1: CMEVT_INSERVICE in CMST_ONHOOK endpt state

## cmUpdateTPSAExtReg:4905 endpt cmEndpt[0].inservice=0 ##
## cmUpdateTPSAExtReg:4906 i     cmEndpt[1].inservice=0 ##
#### cmProcessCallEvent:430 cmEndpt[0].regRetryTimerMs = 60000 ###

cmEndpt: 0, cid -1: CMEVT_INSERVICE in CMST_ONHOOK endpt state

cmEndpt: 1, cid -1: CMEVT_INSERVICE in CMST_ONHOOK endpt state

## cmUpdateTPSAExtReg:4905 endpt cmEndpt[0].inservice=0 ##
## cmUpdateTPSAExtReg:4906 i     cmEndpt[1].inservice=0 ##
#### cmProcessCallEvent:430 cmEndpt[0].regRetryTimerMs = 60000 ###

cmEndpt: 0, cid -1: CMEVT_INSERVICE in CMST_ONHOOK endpt state

cmEndpt: 1, cid -1: CMEVT_INSERVICE in CMST_ONHOOK endpt state

## cmUpdateTPSAExtReg:4905 endpt cmEndpt[0].inservice=0 ##
## cmUpdateTPSAExtReg:4906 i     cmEndpt[1].inservice=0 ##
#### cmProcessCallEvent:430 cmEndpt[0].regRetryTimerMs = 60000 ###


Co mi się rzuciło w oczy?

"BusyBox v1.00 (2017.06.06-11:21+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands."

Czy w jakiś sposób można się do tego wbić?

"initVodslBoundIpIfLanSideUpLocked:380 ######### LAN use TPSA Virtual Interface, br0ipAddr =172.28.130.173 ################"

Po wpisaniu tego w adres przeglądarki ładuje się to samo co po wpisaniu domyslnego 10.0.0.1

3223:

CFE version 1.0.37-110.4-1 for BCM96368 (32bit,SP,BE)
Build Date: Tue Mar 22 16:44:22 CST 2011 (adams@rd7-server)
Copyright (C) 2000-2009 Broadcom Corporation.

Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB
Total Flash size: 8192K with 135 sectors
Chip ID: BCM6368B2, MIPS: 400MHz
Main Thread: TP0
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000

Board IP address                  : 192.168.1.1
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id (0-15)                   : 96368MIT-1341N
Number of MAC Addresses (1-32)    : 32
Base MAC Address                  : d8:b6:b7:77:e9:72
PSI Size (1-64) KBytes            : 24
Enable Backup PSI [0|1]           : 0
System Log Size (0-256) KBytes    : 0
Main Thread Number [0|1]          : 0
Serial Number                     : 153QLA00700
Voice Board Configuration (0-0)   : ADVNgr_3223u

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x802b0480
Decompression OK!
Entry at 0x802b0480
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x802b0480
Linux version 2.6.30 (herbert@rd7-server) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #2 Wed Jan 8 12:31:06 CST 2014
Parallel flash device: name AM29DL800B, id 0x22cb size 8192KB
96368MIT-1341N prom init
Linux TP ID = 0
CPU revision is: 0002a031 (Broadcom4350)
Determined physical RAM map:
 memory: 03ece000 @ 00000000 (usable)
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  Normal   0x00001000 -> 0x00003ece
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00003ece
On node 0 totalpages: 16078
free_area_init_node: node 0, pgdat 803454b0, node_mem_map 81000000
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 94 pages used for memmap
  Normal zone: 11888 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 15952
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
NR_IRQS:128
PID hash table entries: 256 (order: 8, 1024 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Allocating memory for DSP module core and initialization code
Allocated DSP module memory - CORE=0x8108c720 SIZE=1590816, INIT=0x81210d40 SIZE=44
Memory: 58456k/64312k available (2713k kernel code, 5836k reserved, 576k data, 124k init, 0k highmem)
Calibrating delay loop... 399.36 BogoMIPS (lpj=199680)
Mount-cache hash table entries: 512
--Kernel Config--
  SMP=0
  PREEMPT=0
  DEBUG_SPINLOCK=0
  DEBUG_MUTEXES=0
Broadcom Logger v0.1 Jan  8 2014 12:26:44
net_namespace: 816 bytes
NET: Registered protocol family 16
Total Flash size: 8192K with 135 sectors
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:01.0: reg 10 32bit mmio: [0x000000-0x00ffff]
pci 0000:00:09.0: reg 10 32bit mmio: [0x10001600-0x100016ff]
pci 0000:00:0a.0: reg 10 32bit mmio: [0x10001500-0x100015ff]
BLOG v3.0 Initialized
BLOG Rule v1.0 Initialized
Broadcom IQoS v0.1 Jan  8 2014 12:30:02 initialized
Broadcom GBPM v0.1 Jan  8 2014 12:30:02 initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
fuse init (API version 7.11)
msgmni has been set to 114
io scheduler noop registered (default)
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
bcm963xx_mtd driver v1.0
File system address: 0xb8010100
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 15, io mem 0x10001500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 13, io mem 0x10001600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x8017 is enabled
Serial: BCM63XX driver $Revision: 3.00 $
Magic SysRq enabled (type ^ h for list of supported commands)
ttyS0 at MMIO 0xb0000100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 11) is a BCM63XX
Total # RxBds=2960
bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized

bcmxtmrt: Broadcom BCM6368B2 ATM/PTM Network Device v0.3 Jan  8 2014 12:29:45
IPSEC SPU: SUCCEEDED
GACT probability NOT on
Mirror/redirect action on
u32 classifier
    input device check on
    Actions configured
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Bridge firewalling registered
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing unused kernel memory: 124k freed
init started:  BusyBox v1.00 (2014.01.08-04:33+0000) multi-call binary


BusyBox v1.00 (2014.01.08-04:33+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.


Loading drivers and kernel modules...

ct_hotplug_monitor: not found
206
bcm_ingqos: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Broadcom Ingress QoS Module  Char Driver v0.1 Jan  8 2014 12:28:31 Registered<243>

Broadcom Ingress QoS ver 0.1 initialized
BPM: tot_mem_size=67108864B (64MB), buf_mem_size=10066329B (9MB), num of buffers=4802, buf size=2096
Broadcom BPM Module Char Driver v0.1 Jan  8 2014 12:27:17 Registered<244>
[NTC bpm] bpm_set_status: BPM status : enabled

Initialized fcache state
Broadcom Packet Flow Cache  Char Driver v2.2 Jan  8 2014 12:28:36 Registered<242>
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
Constructed Broadcom Packet Flow Cache v2.2 Jan  8 2014 12:28:36
CMF:CONFIG cmfConstruct:
CMF:CONFIG pktDbgLvl[0xc00dd9e4]=0
CMF:HAL pktCmfHalConstruct:
CMF:HAL pktDbgLvl[0xc00d569c]=0
CMF:HAL pktCmfHalConstruct:
CMF:HAL pktDbgLvl[0xc00d569c]=0
CMF:DRV pktCmfDrvConstruct:
CMF:DRV pktDbgLvl[0xc00dd9f4]=0
Broadcom Packet CMF (Experimental) Char Driver v0.1 Jan  8 2014 12:28:35 Registered<232>
CMF:PROTO pktCmfProtoConstruct:
CMF:PROTO pktDbgLvl[0xc00dd9c0]=0
Broadcom Packet CMF (Experimental) [6368-B2] v0.1 Jan  8 2014 12:28:34 Loaded
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM6368B2 Ethernet Network Device v0.1 Jan  8 2014 12:29:40
ETH Init: Ch:0 - 180 tx BDs at 0xa3958000
ETH Init: Ch:0 - 960 rx BDs at 0xa2a94000
######## ethsw_init_table:105 ####### switch_port_phyid[0]=1
######## ethsw_init_table:105 ####### switch_port_phyid[1]=2
######## ethsw_init_table:105 ####### switch_port_phyid[2]=3
######## ethsw_init_table:105 ####### switch_port_phyid[3]=4
######## ethsw_init_table:105 ####### switch_port_phyid[4]=17
/proc/buffer16 created
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
CMF:HW pktDbgLvl[0xc00ce640]=0
CMF:HW pktCmfHwReset: Reset HW layer.
Broadcom Packet CMF (Experimental) SWC RESET.
BRCM Ext Switch: Tag <0:0x0:0> Port<0>
Broadcom Packet CMF (Experimental) SWC INITIALIZED.
CMF:FWD pktCmfFwdDevConstruct:
CMF:FWD pktDbgLvl[0xc00ddc64]=0
Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Jan  8 2014 12:28:35 Registered
CMF Fwd Hnd DbgLvl <0xc00ddc90> = <0>
CMF:FWD pktCmfFwdDevConstruct:
CMF:FWD pktDbgLvl[0xc00ddc64]=0
Broadcom Packet CMF (Experimental) Forwarder Net Device 0 v0.1 Jan  8 2014 12:28:35 Registered
CMF Fwd Hnd DbgLvl <0xc00ddc90> = <0>
Broadcom Packet CMF (Experimental) ENABLED.
===== Found Interface name mapping : 96368MIT-1341N =====
eth1: MAC Address: D8:B6:B7:77:E9:72
eth2: MAC Address: D8:B6:B7:77:E9:72
eth3: MAC Address: D8:B6:B7:77:E9:72
eth4: MAC Address: D8:B6:B7:77:E9:72
eth0: MAC Address: D8:B6:B7:77:E9:72
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:01.0 to 64
wl: passivemode=1
wl: napimode=0
wl: allocskbmode=1
wl:srom strapped
wl:(srom strapped) probe/present=0
wl:srom not detected, using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm43222_map.bin
wl0: Broadcom BCMa8d6 802.11 Wireless Controller 5.100.123.0.cpe4.10L02.6
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
IRQ 21/brcm_21: IRQF_DISABLED is not guaranteed on shared IRQs
DSP Driver: DSP init stub
Endpoint: endpoint_init entry
Endpoint: endpoint_init COMPLETED
p8021ag: p8021ag_init entry
Broadcom 802.1Q VLAN Interface, v0.1
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
usbcore: registered new interface driver hso
hso: 1.6-Option:USB High Speed Option driver

===== Comtrend Release Version M631-S410TPS-C07_R01_v3 =====

ssk:error:13.490:BOS: Enter bosInit
lck_checkBeforeEBOS: Exit bosInit
ntry:171:lock reendpoint_open COMPLETED
quired during cmsObj_getNextInSubTreeFlags
ip_tables: (C) 2000-2006 Netfilter Core Team
/proc/PSD_data created
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (2500 buckets, 10000 max)
iptables: Table Rule Change
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: Table Rule Change
iptables: Table Rule Change
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: Table Rule Change
iptables: Table Rule Change
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: Table Rule Change
iptables: Table Rule Change
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: No chain/target/match by that name
iptables: Table Rule Change
iptables: Table Rule Change
device eth1 entered promiscuous mode
######## bcm63xx_enet_open:1339 ####### dev->base_addr=0 phyport:0 0
device eth2 entered promiscuous mode
######## bcm63xx_enet_open:1339 ####### dev->base_addr=1 phyport:0 1
device eth3 entered promiscuous mode
######## bcm63xx_enet_open:1339 ####### dev->base_addr=2 phyport:1 2
device eth4 entered promiscuous mode
######## bcm63xx_enet_open:1339 ####### dev->base_addr=3 phyport:2 3
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
BcmAdsl_Initialize=0xC016CF38, g_pFnNotifyCallback=0xC019FE14
kerSysGetSerialNumber: sn is 153QLA00700
Clocks for QPROC and AFE are being aligned with step through ...
AFE is aligned, i = 064, PhaseValue = -050, PhaseCntl = 0x3FC00000
QPROC is aligned, i = 015, PhaseValue = 0050, PhaseCntl = 0x3FC0400F
Clocks for QPROC and AFE are aligned with syn_status AFE = 0x70, QPROC = 0x78
AFE  phase control reg @0xb0f570f8 default actual = 0x0021C38F, exp = 0x0021c38f
QPRC phase control reg @0xb0f5f0c0 default actual = 0x0421C38F, exp = 0x0421c38f
WLmngr Daemon is running
optarg=0 shmId=0
pSdramPHY=0xA3FFFFF8, 0xFFFFD7FF 0xFFBFDFFE
*** XfaceOffset: 0x5FF90 => 0x5FF90 ***
wlevt is ready for new msg...
*** PhySdramSize got adjusted: 0xD8C2C => 0x10F350 ***
AdslCoreSharedMemInit: shareMemSize=142477(142480)
AdslCoreHwReset:  pLocSbSta=81498000 bkupThreshold=3072
AdslCoreHwReset:  AdslOemDataAddr = 0xA3F9B184
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
XTM Init: 512 rx BDs at 0xa1cf0000
XTM Init: 16 rx BDs at 0xa1f82c80
Register interface pppoa0 !!
Register interface ppp1.1 !!
######## bcm63xx_enet_open:1339 ####### dev->base_addr=5 phyport:5 5
####reset_IP1001:512 #### IP1001 Reset OK !! phyAddr=0x11
Register interface ppp2.1 !!
group[0] = 0x1df
Success
Success
Success
Success
monitor task is initialized pid= 306
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
br0: port 5(wl0) entering disabled state
Switch MDK: num_switches = 1
Switch MDK: unit = 0; phy_pbmp = 0x2f; config_pbmp = 0x2f
Switch MDK link poll thread: unit=0; phypbmp=0x2f
##### ethsw_IP1001_init:8034 #####
####reset_IP1001:512 #### IP1001 Reset OK !! phyAddr=0x11
There is no Predefined DevicePin in CFE
WPS Device PIN = 12715657
Setting SSID: "COMTREND-VI-3223u-E972"
Setting SSID: "wl0_Guest1"
Setting SSID: "wl0_Guest2"
Setting SSID: "wl0_Guest3"
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
UPnP daemon is ready to run
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: scan in progress ...
acsd: selected channel spec: 0x2b01


3036:

HELO
CPUI
L1CI
HELO
CPUI
L1CI
DRAM
----
PHYS
STRF
400H
PHYE
DDR2
SIZ4
SIZ3
SIZ2
SIZ1
DINT
USYN
LSYN
MFAS
LMBE
RACE
PASS
----
ZBSS
CODE
DATA
L12F
MAIN


CFE version 1.0.38-112.118-39 for BCM963268 (32bit,SP,BE)
Build Date: Thu Jan 16 16:03:42 CST 2014 (rick@rd6-server)
Copyright (C) 2000-2011 Broadcom Corporation.

HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
Total Flash size: 16384K with 4096 sectors
Chip ID: BCM63168D0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000

Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id (0-32)                   : 963168M-1441N3
Number of MAC Addresses (1-32)    : 32
Base MAC Address                  : d8:b6:b7:90:4a:e5
PSI Size (1-64) KBytes            : 64
Enable Backup PSI [0|1]           : 0
System Log Size (0-256) KBytes    : 0
Main Thread Number [0|1]          : 0
WLAN Password                     : 0
Serial Number                     : 158QRA00486

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x8031d610
Decompression OK!
Entry at 0x8031d610
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
0 buffers found.
Closing DMA Channels.
Starting program at 0x8031d610
Linux version 2.6.30 (herbert@localhost.localdomain) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 SMP PREEMPT Tue May 23 11:48:46 CST 2017
HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
963168M-1441N3 prom init
CPU revision is: 0002a080 (Broadcom4350)
DSL SDRAM reserved: 0x132000
Determined physical RAM map:
 memory: 03ece000 @ 00000000 (usable)
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  Normal   0x00001000 -> 0x00003ece
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00003ece
On node 0 totalpages: 16078
free_area_init_node: node 0, pgdat 803e2120, node_mem_map 81000000
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 4064 pages, LIFO batch:0
  Normal zone: 94 pages used for memmap
  Normal zone: 11888 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 15952
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
NR_IRQS:128
PID hash table entries: 256 (order: 8, 1024 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 59316k/64312k available (3157k kernel code, 4976k reserved, 772k data, 152k init, 0k highmem)
Calibrating delay loop... 398.33 BogoMIPS (lpj=199168)
Mount-cache hash table entries: 512
--Kernel Config--
  SMP=1
  PREEMPT=1
  DEBUG_SPINLOCK=0
  DEBUG_MUTEXES=0
Broadcom Logger v0.1 May 23 2017 11:46:44
CPU revision is: 0002a080 (Broadcom4350)
Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Calibrating delay loop... 402.43 BogoMIPS (lpj=201216)
Brought up 2 CPUs
net_namespace: 1144 bytes
NET: Registered protocol family 16
Total Flash size: 16384K with 4096 sectors
Internal 1P2 VREG will be shutdown if unused...Used, leave it on (00008b3b-000085d2=1385>=300)
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10013fff]
pci 0000:00:00.0: reg 30 32bit mmio: [0x000000-0x0007ff]
pci 0000:00:00.0: supports D1 D2
pci 0000:00:00.0: PME# supported from D0 D3hot D3cold
pci 0000:00:00.0: PME# disabled
pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff]
pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff]
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0:   IO window: disabled
pci 0000:01:00.0:   MEM window: disabled
pci 0000:01:00.0:   PREFETCH window: disabled
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v3.0 Initialized
BLOG Rule v1.0 Initialized
Broadcom IQoS v0.1 May 23 2017 11:48:36 initialized
Broadcom GBPM v0.1 May 23 2017 11:48:36 initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
fuse init (API version 7.11)
msgmni has been set to 115
io scheduler noop registered (default)
PCI: Setting latency timer of device 0000:01:00.0 to 64
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
PPPoL2TP kernel driver, V1.0
bcm963xx_mtd driver v1.0
File system address: 0xb8010100
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 18, io mem 0x10002500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
@@@@@ hub_power_on:541 @@@@@
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 17, io mem 0x10002600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
@@@@@ hub_power_on:541 @@@@@
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0xc007 is enabled
PCIe: No device found - Powering down
Serial: BCM63XX driver $Revision: 3.00 $
Magic SysRq enabled (type ^ h for list of supported commands)
ttyS0 at MMIO 0xb0000180 (irq = 13) is a BCM63XX
ttyS1 at MMIO 0xb00001a0 (irq = 42) is a BCM63XX
bcmPktDma_init: Broadcom Packet DMA Library initialized
Total # RxBds=1448
bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized

bcmxtmrt: Broadcom BCM3168D0 ATM/PTM Network Device v0.5 May 23 2017 11:48:27
IPSEC SPU: SUCCEEDED
GACT probability NOT on
Mirror/redirect action on
u32 classifier
    input device check on
    Actions configured
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 10
IPv6 over IPv4 tunneling driver
NET: Registered protocol family 17
NET: Registered protocol family 15
Bridge firewalling registered
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing unused kernel memory: 152k freed
init started: BusyBox v1.17.2 (2017-05-23 11:51:41 CST)
starting pid 214, tty '': '/etc/init.d/rcS'
starting pid 220, tty '': '-/bin/sh'


BusyBox v1.17.2 (2017-05-23 11:51:41 CST) built-in shell (ash)
Enter 'help' for a list of built-in commands.


Loading drivers and kernel modules...

-/bin/sh: ct_hotplug_monitor: not found
chipinfo: module license 'proprietary' taints kernel.
Disabling lock debugging due to kernel taint
brcmchipinfo: brcm_chipinfo_init entry
Broadcom Ingress QoS Module  Char Driver v0.1 May 23 2017 11:47:06 Registered<243>

Broadcom Ingress QoS ver 0.1 initialized
BPM: tot_mem_size=67108864B (64MB), buf_mem_size=10066320B (9MB), num of buffers=4766, buf size=2112
Broadcom BPM Module Char Driver v0.1 May 23 2017 11:47:01 Registered<244>
[NTC bpm] bpm_set_status: BPM status : enabled

NBUFF v1.0 Initialized
Initialized fcache state
Broadcom Packet Flow Cache  Char Driver v2.2 May 23 2017 11:47:06 Registered<242>
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Broadcom Packet Flow Cache learning via BLOG enabled.
Constructed Broadcom Packet Flow Cache v2.2 May 23 2017 11:47:06
chipId 0x631680D0
Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 May 23 2017 11:47:02 Registered <241>
FAP Debug values at 0x00000010 0x00000010
Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000
FAP Soft Reset Done
4ke Reset Done
Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000
FAP Soft Reset Done
4ke Reset Done
FAP Debug values at 0xa259b590 0xa261b590
Allocated FAP0 GSO Buffers (0xA25A19E8) : 1048576 bytes @ 0xA2700000
Allocated FAP1 GSO Buffers (0xA26219E8) : 1048576 bytes @ 0xA2000000
Allocated FAP0 TM SDRAM Queue Storage (a25a19ec) : 219456 bytes @ a2540000
Allocated FAP1 TM SDRAM Queue Storage (a26219ec) : 219456 bytes @ a2680000
[NTC fapProto] fapReset  : Reset FAP Protocol layer
[FAP0] DSPRAM : stack <0x80000000><1536>, global <0x80000600><6592>, free <64>, total<8192>
[FAP1] DSPRAM : stack <0x80000000><1536>, global <0x80000600><6592>, free <64>, total<8192>
[FAP0] PSM : addr<0x80002000>, used <24512>, free <64>, total <24576>
[FAP1] PSM : addr<0x80002000>, used <24512>, free <64>, total <24576>
[FAP0] Flows supported: 226 (dsp 56, psm 45, qsm 125)
[FAP1] Flows supported: 226 (dsp 56, psm 45, qsm 125)
[FAP0] DQM : availableMemory 14680 bytes, nextByteAddress 0xE00106A8
[FAP1] DQM : availableMemory 14680 bytes, nextByteAddress 0xE00106A8
[FAP0] GSO Buffer set to 0xA2700000
[FAP1] GSO Buffer set to 0xA2000000
[FAP0] FAP BPM Initialized.
[FAP1] FAP BPM Initialized.
fapDrv_construct: FAP0: pManagedMemory=b0820710. wastage 8 bytes
fapDrv_construct: FAP1: pManagedMemory=b0a20710. wastage 8 bytes
bcmPktDma_bind: FAP Driver binding successfull
[FAP0] FAP TM: ON
[FAP1] FAP TM: ON
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCM63168D0 Ethernet Network Device v0.1 May 23 2017 11:48:22
fapDrv_psmAlloc: fapIdx=0, size: 4000, offset=b0820710 bytes remaining 7000
ETH Init: Ch:0 - 200 tx BDs at 0xb0820710
fapDrv_psmAlloc: fapIdx=1, size: 4000, offset=b0a20710 bytes remaining 7000
ETH Init: Ch:1 - 200 tx BDs at 0xb0a20710
fapDrv_psmAlloc: wastage 8 bytes
fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b08216b0 bytes remaining 2184
ETH Init: Ch:0 - 600 rx BDs at 0xb08216b0
fapDrv_psmAlloc: wastage 8 bytes
fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a216b0 bytes remaining 2184
ETH Init: Ch:1 - 600 rx BDs at 0xb0a216b0
For port 3; changing the MII adv to 0x1e1
changing the GMII adv to 0x0
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
devname_by_phyid: get Eth index fail
eth1: MAC Address: D8:B6:B7:90:4A:E5
devname_by_phyid: get Eth index fail
eth2: MAC Address: D8:B6:B7:90:4A:E5
devname_by_phyid: get Eth index fail
eth3: MAC Address: D8:B6:B7:90:4A:E5
devname_by_phyid: get Eth index fail
eth0: MAC Address: D8:B6:B7:90:4A:E5
BCM63XX_USB USB Device not present
insmod: can't insert '/lib/modules/2.6.30/extra/bcm_usb.ko': No such device
[NTC arl] arlEnable : Enabled ARL binding to FAP
Broadcom Adress Resolution Logic Processor (ARL) Char Driver v0.1 May 23 2017 11:47:00 Registered <245>
[ERROR fap] keepAliveWd_timer,722: keepAliveWd_timer: Detected scribble error for FAP0

[ERROR fap] keepAliveWd_timer,723: PSM scribble 0 (b0820024)=0x00005fc0 / 0x00005fb0

[ERROR fap] keepAliveWd_timer,724: PSM scribble 1 (b0820028)=0x12345678 / 0x12345678

[ERROR fap] keepAliveWd_timer,725: PSM scribble 2 (b08206f4)=0x12345678 / 0x12345678

[ERROR fap] keepAliveWd_timer,726: PSM scribble 3 (b0823208)=0x12345678 / 0x12345678

[ERROR fap] keepAliveWd_timer,727: PSM scribble 4 (b0823210)=0x12345678 / 0x12345678

[ERROR fap] keepAliveWd_timer,728: QSM scribble 0 (b0c04000)=0x00005fc0 / 0x0000c6a8

[ERROR fap] keepAliveWd_timer,729: QSM scribble 1 (b0c106a4)=0x12345678 / 0x12345678

[ERROR fap] keepAliveWd_timer,722: keepAliveWd_timer: Detected scribble error for FAP1

[ERROR fap] keepAliveWd_timer,723: PSM scribble 0 (b0a20024)=0x00005fc0 / 0x00005fb0

[ERROR fap] keepAliveWd_timer,724: PSM scribble 1 (b0a20028)=0x12345678 / 0x12345678

[ERROR fap] keepAliveWd_timer,725: PSM scribble 2 (b0a206f4)=0x12345678 / 0x12345678

[ERROR fap] keepAliveWd_timer,726: PSM scribble 3 (b0a23208)=0x12345678 / 0x12345678

[ERROR fap] keepAliveWd_timer,727: PSM scribble 4 (b0a23210)=0x12345678 / 0x12345678

[ERROR fap] keepAliveWd_timer,728: QSM scribble 0 (b0e04000)=0x00005fc0 / 0x0000c6a8

[ERROR fap] keepAliveWd_timer,729: QSM scribble 1 (b0e106a4)=0x12345678 / 0x12345678

--SMP support
wl: dsl_tx_pkt_flush_len=338
wl: high_wmark_tot=3097
PCI: Setting latency timer of device 0000:00:00.0 to 64
wl: passivemode=1
wl: napimode=0
wl0: allocskbmode=1 currallocskbsz=256
Neither SPROM nor OTP has valid image
wl:srom/otp not programmed, using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm6362_map.bin
srom rev:8
wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=16
wl0: Broadcom BCM435f 802.11 Wireless Controller 6.30.102.7.cpe4.12L06B.1
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
Broadcom 802.1Q VLAN Interface, v0.1
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
hso_init - tty_register_driver failed(-16)
insmod: can't insert '/lib/modules/2.6.30/kernel/drivers/usb/serial/hso.ko': Device or resource busy

===== Comtrend Release Version NA31-412TPS-C09_R03 =====

-- Delete 0 WANDelegated Prefix --
-- Delete 0 Loopback static route --
ip_tables: (C) 2000-2006 Netfilter Core Team
/proc/PSD_data created
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (2500 buckets, 10000 max)
[!] @@@@@ nf_conntrack_init:1561 @@@@@ !
ctnetlink v0.93: registering with nfnetlink.
ip6_tables: (C) 2000-2006 Netfilter Core Team
Host MIPS Clock divider pwrsaving is enabled
DDR Self Refresh pwrsaving is enabled
Energy Efficient Ethernet is disabled
Adaptive Voltage Scaling is now enabled
BcmPwrMngtEnableAvs: AVS_START, 0x838df218
device eth1 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth1: link is not ready
device eth2 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth2: link is not ready
device eth3 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth3: link is not ready
device eth0 entered promiscuous mode
ADDRCONF(NETDEV_UP): eth0: link is not ready
[ll] EUI-64 mdoe
*** dslThread dslPid=1624
BcmAdsl_Initialize=0xC01F44E4, g_pFnNotifyCallback=0xC0237054
lmemhdr[2]=0x100CE000, pAdslLMem[2]=0x100CE000
pSdramPHY=0xA3FFFFF8, 0x70F0B2F0 0xF0F070F0
*** XfaceOffset: 0x5FF90 => 0x5FF90 ***
*** PhySdramSize got adjusted: 0xEB214 => 0x121CB0 ***
AdslCoreSharedMemInit: shareMemSize=66349(66352)
AdslCoreHwReset:  pLocSbSta=81700000 bkupThreshold=3072
AdslCoreHwReset:  AdslOemDataAddr = 0xA3FAA198
AdslCoreInit: System Vendor ID in EOC = B500434D5444544D
AdslCoreInit: PhyVersion in EOC = A2pv6F039.d24k
***BcmDiagsMgrRegisterClient: 0 ***
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
fapDrv_psmAlloc: fapIdx=1, size: 1600, offset=b0a22980 bytes remaining 584
XTM Init: Ch:0 - 200 rx BDs at 0xb0a22980
fapDrv_psmAlloc: fapIdx=1, size: 128, offset=b0a22fc0 bytes remaining 456
XTM Init: Ch:1 - 16 rx BDs at 0xb0a22fc0
bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system
WLmngr Daemon is running
optarg=Register interface pppoa0 !!
0 shmId=0
wlevt is ready for new msg...
Register interface ppp1.1 !!
Could not get lock!
monitor task is initialized pid= 339
There is no Predefined DevicePin in CFE
WPS Device PIN = 20554606
ssk:debug:39.639:initialFirewall:1007:Enter.
Note: Loading 6300 MDK (default) driver for 63168 chip
Switch MDK: num_switches = 1
Switch MDK: unit = 0; phy_pbmp = 0xf; config_pbmp = 0xf
Switch MDK link poll thread: unit=0; phypbmp=0xf
Setting SSID: "Comtrend_9201"
Setting SSID: "wl0_Guest1"
Setting SSID: "wl0_Guest2"
Setting SSID: "wl0_Guest3"


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
Wyświetl posty nie starsze niż:  Sortuj wg  
Nowy temat Odpowiedz w temacie  [ Posty: 45 ]  Przejdź na stronę Poprzednia  1, 2, 3

Strefa czasowa UTC+1godz. [letni]


Kto jest online

Użytkownicy przeglądający to forum: Obecnie na forum nie ma żadnego zarejestrowanego użytkownika i 1 gość


Nie możesz tworzyć nowych tematów
Nie możesz odpowiadać w tematach
Nie możesz zmieniać swoich postów
Nie możesz usuwać swoich postów

Szukaj:
Przejdź do:  
designed by digi-led.pl
...Copyright © 2010-2013, Ekipa openrouter.info