Dzisiaj jest 16 lip 2018, 18:42

Strefa czasowa UTC+1godz. [letni]




Nowy temat Odpowiedz w temacie  [ Posty: 293 ]  Przejdź na stronę Poprzednia  1 ... 9, 10, 11, 12, 13, 14, 15  Następna
Autor Wiadomość
 Tytuł: Re: dwr-960 LTE
Post: 10 kwie 2018, 15:02 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 315
Starting kernel @80000000...
[ 0.000000] Linux version 4.9.86 (krolik@krolik-T420) (gcc version 7.3.0 (Ope nWrt GCC 7.3.0 r6443+3-d88e928) ) #0 Wed Apr 4 17:58:37 2018
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is D-Link DWR-960
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs 2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00004f20
[ 0.000000] Readback ErrCtl register=00004f20
[ 0.000000] Memory: 60428K/65536K available (3126K kernel code, 158K rwdata, 756K rodata, 176K init, 217K bss, 5108K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_n s: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_i dle_ns: 6590553264 ns
[ 0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 74051 15902ns
[ 0.015462] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.080603] pid_max: default: 32768 minimum: 301
[ 0.089885] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.102938] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.122918] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns
[ 0.142399] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.154542] pinctrl core: initialized pinctrl subsystem
[ 0.165474] NET: Registered protocol family 16
[ 0.195687] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.206716] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.219250] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.230232] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.242758] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.253735] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.266240] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.277037] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.293057] clocksource: Switched to clocksource systick
[ 0.304682] NET: Registered protocol family 2
[ 0.314103] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.327877] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.340470] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.353193] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.364726] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.377392] NET: Registered protocol family 1
[ 0.388197] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.400842] Crashlog allocated RAM at address 0x3f00000
[ 0.412288] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.432530] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.444021] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.471997] io scheduler noop registered
[ 0.479697] io scheduler deadline registered (default)
[ 0.490072] ralink-usb-phy usbphy: invalid resource
[ 0.500168] gpio-export gpio_export: 1 gpio(s) exported
[ 0.510633] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.524182] console [ttyS0] disabled
[ 0.531169] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.550945] console [ttyS0] enabled
[ 0.550945] console [ttyS0] enabled
[ 0.564723] bootconsole [early0] disabled
[ 0.564723] bootconsole [early0] disabled
[ 0.584952] spi spi0.0: force spi mode3
[ 0.604034] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.613458] 3 ofpart partitions found on MTD device spi0.0
[ 0.624391] Creating 3 MTD partitions on "spi0.0":
[ 0.633948] 0x000000000000-0x000000010000 : "jboot"
[ 0.645236] 0x000000010000-0x000000ff0000 : "firmware"
[ 0.657550] 2 jimage-fw partitions found on MTD device firmware
[ 0.669428] 0x000000010000-0x00000015cc61 : "kernel"
[ 0.680978] 0x00000015cc61-0x000000ff0000 : "rootfs"
[ 0.692640] mtd: device 3 (rootfs) set to be root filesystem
[ 0.704467] 1 squashfs-split partitions found on MTD device rootfs
[ 0.716838] 0x000000363000-0x000000ff0000 : "rootfs_data"
[ 0.729123] 0x000000ff0000-0x000001000000 : "config"
[ 0.741368] libphy: Fixed MDIO Bus: probed
[ 0.753246] gsw: setting port4 to ephy mode
[ 0.761618] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 3 link u p (100Mbps/Full duplex)
[ 0.779851] mtk_soc_eth 10100000.ethernet: generated random MAC address 6e:e5 :a1:fe:75:2c
[ 0.796316] libphy: mdio: probed
[ 0.837166] mtk_soc_eth 10100000.ethernet: connected port 5 to PHY at mdio-bu s:07 [uid=004dd072, driver=Atheros 8035 ethernet]
[ 0.859967] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 0.872511] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0 100000, irq 5
[ 0.889485] rt2880_wdt 10000120.watchdog: Initialized
[ 0.900618] NET: Registered protocol family 10
[ 0.912402] NET: Registered protocol family 17
[ 0.921387] 8021q: 802.1Q VLAN Support v1.8
[ 0.938373] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 0.953404] Freeing unused kernel memory: 176K
[ 0.962286] This architecture does not have kernel memory protection.
[ 1.672376] init: Console is alive
[ 1.679467] init: - watchdog -
[ 2.327037] random: fast init done
[ 2.764801] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.909707] usbcore: registered new interface driver usbfs
[ 2.920806] usbcore: registered new interface driver hub
[ 2.931526] usbcore: registered new device driver usb
[ 2.947244] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.961949] ehci-platform: EHCI generic platform driver
[ 2.982723] phy phy-usbphy.0: remote usb device wakeup disabled
[ 2.994530] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 3.003418] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 3.014906] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 3.030810] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 3.051437] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 3.064921] hub 1-0:1.0: USB hub found
[ 3.072788] hub 1-0:1.0: 1 port detected
[ 3.084438] kmodloader: done loading kernel modules from /etc/modules-boot.d/ *
[ 3.102943] init: - preinit -
[ 4.278328] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4.290034] 8021q: adding VLAN 0 to HW filter on device eth0
[ 4.301798] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.672053] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 5.722069] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 5.857308] procd: - early -
[ 5.863235] procd: - watchdog -
[ 6.227536] procd: - watchdog -
[ 6.234069] procd: - ubus -
[ 6.453849] procd: - init -
Please press Enter to activate this console.
[ 6.791859] kmodloader: loading kernel modules from /etc/modules.d/*
[ 6.810795] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 6.834420] usbcore: registered new interface driver cdc_wdm
[ 6.847759] Loading modules backported from Linux version wt-2017-11-01-0-gfe 248fc2c180
[ 6.863781] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 6.881341] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 6.900905] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 6.976166] xt_time: kernel timezone is -0000
[ 7.146591] PPP generic driver version 2.4.2
[ 7.157871] NET: Registered protocol family 24
[ 7.169314] usbcore: registered new interface driver qmi_wwan
[ 7.210475] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEP ROM data from 'soc_wmac.eeprom'.
[ 7.230475] rt2800_wmac 10180000.wmac: Direct firmware load for soc_wmac.eepr om failed with error -2
[ 7.248702] rt2800_wmac 10180000.wmac: Falling back to user helper
[ 7.564251] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 d etected
[ 7.579774] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 7.626061] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 11.712799] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 15.305474] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 15.354038] jffs2_build_filesystem(): unlocking the mtd device... [ 15.3827 58] done.
[ 15.386604] jffs2_build_filesystem(): erasing all blocks after the end marker ... [ 20.376195] 8021q: adding VLAN 0 to HW filter on device eth0
[ 20.453349] device eth0 entered promiscuous mode
[ 20.500809] br-lan: port 1(eth0.1) entered blocking state
[ 20.511661] br-lan: port 1(eth0.1) entered disabled state
[ 20.522882] device eth0.1 entered promiscuous mode
[ 20.668082] br-lan: port 1(eth0.1) entered blocking state
[ 20.678915] br-lan: port 1(eth0.1) entered forwarding state
[ 20.690244] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 21.402845] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 46.241853] mtk_soc_eth 10100000.ethernet eth0: port 3 link down
[ 46.254576] br-lan: port 1(eth0.1) entered disabled state
[ 49.374908] mtk_soc_eth 10100000.ethernet eth0: port 3 link up (100Mbps/Full duplex)
[ 49.390826] br-lan: port 1(eth0.1) entered blocking state
[ 49.401610] br-lan: port 1(eth0.1) entered forwarding state



BusyBox v1.27.2 () built-in shell (ash)

_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt SNAPSHOT, r6443+6-d88e928
-----------------------------------------------------
=== WARNING! =====================================
There is no root password defined on this device!
Use the "passwd" command to set up a new password
in order to prevent unauthorized SSH logins.
--------------------------------------------------
root@OpenWrt:/# [ 74.461244] mtk_soc_eth 10100000.ethernet eth0: port 3 link d own
[ 74.473974] br-lan: port 1(eth0.1) entered disabled state
[ 78.704697] mtk_soc_eth 10100000.ethernet eth0: port 2 link up (100Mbps/Full duplex)
[ 78.720592] br-lan: port 1(eth0.1) entered blocking state
[ 78.731383] br-lan: port 1(eth0.1) entered forwarding state
[ 81.321146] mtk_soc_eth 10100000.ethernet eth0: port 2 link down
[ 81.333860] br-lan: port 1(eth0.1) entered disabled state
[ 84.474305] mtk_soc_eth 10100000.ethernet eth0: port 1 link up (100Mbps/Full duplex)
[ 84.490252] br-lan: port 1(eth0.1) entered blocking state
[ 84.501041] br-lan: port 1(eth0.1) entered forwarding state
[ 87.796025] mtk_soc_eth 10100000.ethernet eth0: port 1 link down
[ 87.808746] br-lan: port 1(eth0.1) entered disabled state
[ 108.842907] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (100Mbps/Full duplex)
[ 121.132729] random: crng init done

Informacja, że został wpięty. Adresu lapek wpięty w 5 nie dostaje :(


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 10 kwie 2018, 15:13 
Offline
Użytkownik

Rejestracja: 3 mar 2018, 09:59
Posty: 73
A w kopie licznik odebranych pakietów się zwiększa? Albo na kompie lub routerze rosną liczniki błędów gdzieś?


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 10 kwie 2018, 15:44 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 315
jak wpisuje ifconfig to na eth0.1 Rx i Tx po wpięciu przewodu taki sam jak był


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 11 kwie 2018, 22:11 
Offline
Użytkownik

Rejestracja: 3 mar 2018, 09:59
Posty: 73
https://www.dropbox.com/s/y4qs27rwwkmiy ... y.bin?dl=0
https://www.dropbox.com/s/3gp6wdet0wnj3 ... e.bin?dl=0

Zaczynamy modem. Daj bootlog proszę.
Dokonywałem też zmian w gigabicie, sprawdź go profilaktycznie. ;)


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 12 kwie 2018, 16:45 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 315
Próbowałem wgrywać ale mi dlink gada, że nieprawidłowy firmware. Patrze na wagę a tu 311 KB. Jesteś pewny tego softu?


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 12 kwie 2018, 16:54 
Offline
Użytkownik

Rejestracja: 3 mar 2018, 09:59
Posty: 73
U mnie mają 3585KB. Na pewno dobrze się pobrał?


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 12 kwie 2018, 16:56 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 315
Dobra w innej przeglądarce prawidłowo ściągnęło. Zaraz dam logi


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 12 kwie 2018, 17:11 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 315
Starting kernel @80000000...
[ 0.000000] Linux version 4.9.86 (krolik@krolik-T420) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r6443+3-d88e928) ) #0 Wed Apr 4 17:58:37 2018
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is D-Link DWR-960
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00048001
[ 0.000000] Readback ErrCtl register=00048001
[ 0.000000] Memory: 60428K/65536K available (3126K kernel code, 158K rwdata, 756K rodata, 176K init, 217K bss, 5108K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015462] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.080619] pid_max: default: 32768 minimum: 301
[ 0.089901] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.102953] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.122935] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.142415] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.154558] pinctrl core: initialized pinctrl subsystem
[ 0.165490] NET: Registered protocol family 16
[ 0.195697] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.206726] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.219262] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.230243] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.242769] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.253746] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.266252] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.277049] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.293068] clocksource: Switched to clocksource systick
[ 0.304694] NET: Registered protocol family 2
[ 0.314114] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.327888] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.340481] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.353204] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.364737] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.377404] NET: Registered protocol family 1
[ 0.388210] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.400854] Crashlog allocated RAM at address 0x3f00000
[ 0.412298] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.432538] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.444029] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.472005] io scheduler noop registered
[ 0.479705] io scheduler deadline registered (default)
[ 0.490080] ralink-usb-phy usbphy: invalid resource
[ 0.500174] gpio-export gpio_export: 1 gpio(s) exported
[ 0.510639] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.524188] console [ttyS0] disabled
[ 0.531176] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.550953] console [ttyS0] enabled
[ 0.550953] console [ttyS0] enabled
[ 0.564729] bootconsole [early0] disabled
[ 0.564729] bootconsole [early0] disabled
[ 0.584960] spi spi0.0: force spi mode3
[ 0.604027] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.613450] 3 ofpart partitions found on MTD device spi0.0
[ 0.624384] Creating 3 MTD partitions on "spi0.0":
[ 0.633939] 0x000000000000-0x000000010000 : "jboot"
[ 0.645225] 0x000000010000-0x000000ff0000 : "firmware"
[ 0.657537] 2 jimage-fw partitions found on MTD device firmware
[ 0.669415] 0x000000010000-0x00000015cc39 : "kernel"
[ 0.680963] 0x00000015cc39-0x000000ff0000 : "rootfs"
[ 0.692625] mtd: device 3 (rootfs) set to be root filesystem
[ 0.704452] 1 squashfs-split partitions found on MTD device rootfs
[ 0.716824] 0x000000363000-0x000000ff0000 : "rootfs_data"
[ 0.729108] 0x000000ff0000-0x000001000000 : "config"
[ 0.741354] libphy: Fixed MDIO Bus: probed
[ 0.753141] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 2 link up (100Mbps/Full duplex)
[ 0.771387] mtk_soc_eth 10100000.ethernet: generated random MAC address ae:7a:1b:e1:60:44
[ 0.787854] libphy: mdio: probed
[ 0.828325] mtk_soc_eth 10100000.ethernet: connected port 5 to PHY at mdio-bus:07 [uid=004dd072, driver=Atheros 8035 ethernet]
[ 0.851123] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 0.863670] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 0.880646] rt2880_wdt 10000120.watchdog: Initialized
[ 0.891780] NET: Registered protocol family 10
[ 0.903565] NET: Registered protocol family 17
[ 0.912549] 8021q: 802.1Q VLAN Support v1.8
[ 0.929531] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 0.944563] Freeing unused kernel memory: 176K
[ 0.953444] This architecture does not have kernel memory protection.
[ 1.663136] init: Console is alive
[ 1.670223] init: - watchdog -
[ 2.322031] random: fast init done
[ 2.756979] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 2.902211] usbcore: registered new interface driver usbfs
[ 2.913306] usbcore: registered new interface driver hub
[ 2.924021] usbcore: registered new device driver usb
[ 2.939743] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.954443] ehci-platform: EHCI generic platform driver
[ 2.975217] phy phy-usbphy.0: remote usb device wakeup disabled
[ 2.987023] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 2.995908] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 3.007400] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 3.023303] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 3.043434] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 3.056916] hub 1-0:1.0: USB hub found
[ 3.064787] hub 1-0:1.0: 1 port detected
[ 3.076431] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.094931] init: - preinit -
[ 4.271001] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4.282708] 8021q: adding VLAN 0 to HW filter on device eth0
[ 4.294466] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.185356] jffs2: notice: (342) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 6.218554] mount_root: switching to jffs2 overlay
[ 6.267617] urandom-seed: Seeding with /etc/urandom.seed
[ 6.410630] procd: - early -
[ 6.417232] procd: - watchdog -
[ 6.807564] procd: - watchdog -
[ 6.814161] procd: - ubus -
[ 7.036012] procd: - init -
Please press Enter to activate this console.
[ 7.382893] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.401925] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.425472] usbcore: registered new interface driver cdc_wdm
[ 7.438787] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[ 7.454817] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 7.472353] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.491773] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 7.565389] xt_time: kernel timezone is -0000
[ 7.735645] PPP generic driver version 2.4.2
[ 7.746895] NET: Registered protocol family 24
[ 7.758330] usbcore: registered new interface driver qmi_wwan
[ 7.799578] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
[ 7.820746] ieee80211 phy0: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected
[ 7.836281] ieee80211 phy0: rt2x00_set_rf: Info - RF chipset 7620 detected
[ 7.871724] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 8.371305] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 8.686801] qmi_wwan: probe of 1-1:1.0 failed with error -22
[ 8.709038] qmi_wwan: probe of 1-1:1.1 failed with error -22
[ 8.720752] qmi_wwan 1-1:1.2: bogus CDC Union: master=0, slave=0
[ 8.762408] qmi_wwan 1-1:1.2: cdc-wdm0: USB WDM device
[ 8.803005] qmi_wwan 1-1:1.2 wwan0: register 'qmi_wwan' at usb-101c0000.ehci-1, WWAN/QMI device, fe:11:08:38:fe:e4
[ 8.824066] qmi_wwan 1-1:1.3: bogus CDC Union: master=0, slave=0
[ 8.937630] qmi_wwan 1-1:1.3: cdc-wdm1: USB WDM device
[ 8.960945] qmi_wwan 1-1:1.3 wwan1: register 'qmi_wwan' at usb-101c0000.ehci-1, WWAN/QMI device, fe:11:08:38:fe:e4
[ 9.006602] qmi_wwan 1-1:1.4: cdc-wdm2: USB WDM device
[ 9.113043] qmi_wwan 1-1:1.4 wwan2: register 'qmi_wwan' at usb-101c0000.ehci-1, WWAN/QMI device, fe:11:08:38:fe:e4
[ 15.688226] 8021q: adding VLAN 0 to HW filter on device eth0
[ 15.717526] device eth0 entered promiscuous mode
[ 15.745223] br-lan: port 1(eth0.1) entered blocking state
[ 15.756060] br-lan: port 1(eth0.1) entered disabled state
[ 15.767258] device eth0.1 entered promiscuous mode
[ 15.818546] br-lan: port 1(eth0.1) entered blocking state
[ 15.829370] br-lan: port 1(eth0.1) entered forwarding state
[ 15.840659] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 16.752130] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready


Port 5 nie działa.
Jak dasz radę to zrób proszę aby sysupgrade zaczęło działać. Bo wgranie OFW i potem znowu openwrt zajmuje trochę czasu.

I nie zapomnij o Lucynie


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 12 kwie 2018, 17:18 
Offline
Użytkownik

Rejestracja: 3 mar 2018, 09:59
Posty: 73
Sysupgrade powinno działać. Jeśli w pewnym momencie wisi, to niestety jest normalne na routerach jbootowych z dużym flashem. Na DWR-921 sysupgrade robi się kilkanaście minut łącznie.

Możesz włożyć kartę sim i wykonać polecenie:

uqmi -d /dev/cdc-wdmX --get-signal-info

A potem dać znać które /dev/cdc-wdmX jak odpowiedziało?


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 12 kwie 2018, 17:52 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 315
root@OpenWrt:/# uqmi -d /dev/cdc-wdmX --get-signal-info
Failed to open device
root@OpenWrt:/#


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 12 kwie 2018, 17:53 
Offline
Administrator
Awatar użytkownika

Rejestracja: 10 kwie 2010, 00:28
Posty: 13223
Lokalizacja: Warszawa
/dev/cdc-wdm0 oczywiście zamiast tego X...

_________________
http://eko.one.pl - prawie wszystko o OpenWrt


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 12 kwie 2018, 17:59 
Offline
Użytkownik

Rejestracja: 3 mar 2018, 09:59
Posty: 73
Patrząc po bootlogu to od 0 do 2.


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 12 kwie 2018, 18:05 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 315
root@OpenWrt:/# root@OpenWrt:/# uqmi -d /dev/cdc-wdm0 --get-signal-info
/bin/ash: root@OpenWrt:/#: not found
root@OpenWrt:/# root@OpenWrt:/# uqmi -d /dev/cdc-wdm1 --get-signal-info
/bin/ash: root@OpenWrt:/#: not found
root@OpenWrt:/# root@OpenWrt:/# uqmi -d /dev/cdc-wdm2 --get-signal-info
/bin/ash: root@OpenWrt:/#: not found
root@OpenWrt:/#


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 12 kwie 2018, 18:23 
Offline
Administrator
Awatar użytkownika

Rejestracja: 10 kwie 2010, 00:28
Posty: 13223
Lokalizacja: Warszawa
Zobacz co ty robisz. Jakie root@OpenWrt:/# uqmi -d /dev/cdc-wdm0 --get-signal-info? Jak wklejasz myszą to zrób samo polecenie a nie zgłoszenie basha...

_________________
http://eko.one.pl - prawie wszystko o OpenWrt


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 13 kwie 2018, 14:31 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 315
Zgadza się mój błąd - przepraszam

Teraz już prawidłowo:

root@OpenWrt:/# uqmi -d /dev/cdc-wdm0 --get-signal-info
[ 34.093431] qmi_wwan 1-1:1.2: unknown notification 32 received: index 2 len 2


^C"Failed to conne[ 37.376376] qmi_wwan 1-1:1.2: Error in flush path: -32
ct to service"
root@OpenWrt:/# uqmi -d /dev/cdc-wdm0 --get-signal-info
^C"Failed to conne[ 42.995599] qmi_wwan 1-1:1.2: Error in flush path: -32
ct to service"
root@OpenWrt:/# uqmi -d /dev/cdc-wdm1 --get-signal-info
[ 44.727040] qmi_wwan 1-1:1.3: unknown notification 32 received: index 3 len 2
^C"Failed to conne[ 45.605603] qmi_wwan 1-1:1.3: Error in flush path: -32
ct to service"
root@OpenWrt:/# uqmi -d /dev/cdc-wdm1 --get-signal-info

^C"Failed to conne[ 46.957759] qmi_wwan 1-1:1.3: Error in flush path: -32
ct to service"
root@OpenWrt:/# uqmi -d /dev/cdc-wdm2 --get-signal-info
{
"type": "lte",
"rssi": -83,
"rsrq": -11,
"rsrp": -108,
"snr": 20
}
root@OpenWrt:/#


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 13 kwie 2018, 14:38 
Offline
Użytkownik

Rejestracja: 3 mar 2018, 09:59
Posty: 73
Czyli qmi_wwan 1-1:1.4 będzie naszym typem. W weekend przygotuję już kompletny PR i będziemy testować wszystko poza gigabitem i 5ghz.


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 13 kwie 2018, 15:44 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 315
a 5 też podobno coś obsy pisał, że można aczkolwiek potrzebna by była witamina :D jak dobrze zrozumiałem :)


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 13 kwie 2018, 15:52 
Offline
Administrator
Awatar użytkownika

Rejestracja: 10 kwie 2010, 00:28
Posty: 13223
Lokalizacja: Warszawa
Oficjalnie nie będzie, nie ma drivera do 7610. Nieoficjalnie - wyciekło i możesz sobie sam skompilować, ale to dość drażliwy temat.

_________________
http://eko.one.pl - prawie wszystko o OpenWrt


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 16 kwie 2018, 16:28 
Offline
Użytkownik

Rejestracja: 3 mar 2018, 09:59
Posty: 73
@smereka

Robię porządki w plikach. Możesz wgrać stocka i sprawdzić w konsoli który port się wyświetla po wpięciu kabla do gigabita?


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 17 kwie 2018, 13:54 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 315
Porty 1,2,3 wkładane po kolei i później 1Gbit czyli w naszym przypadku jest to 5. Oraz na końcu 0 u nas WAN:


# ESW: Link Status Changed - Port1 Link UP
ESW: Link Status Changed - Port1 Link Down
ESW: Link Status Changed - Port2 Link UP
ESW: Link Status Changed - Port2 Link Down
ESW: Link Status Changed - Port3 Link UP
ESW: Link Status Changed - Port3 Link Down
ESW: Link Status Changed - Port5 Link UP
ESW: Link Status Changed - Port5 Link Down
ESW: Link Status Changed - Port0 Link UP
ESW: Link Status Changed - Port0 Link Down


Logi oczywiście z OFW


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
Wyświetl posty nie starsze niż:  Sortuj wg  
Nowy temat Odpowiedz w temacie  [ Posty: 293 ]  Przejdź na stronę Poprzednia  1 ... 9, 10, 11, 12, 13, 14, 15  Następna

Strefa czasowa UTC+1godz. [letni]


Kto jest online

Użytkownicy przeglądający to forum: Obecnie na forum nie ma żadnego zarejestrowanego użytkownika i 2 gości


Nie możesz tworzyć nowych tematów
Nie możesz odpowiadać w tematach
Nie możesz zmieniać swoich postów
Nie możesz usuwać swoich postów

Szukaj:
Przejdź do:  
designed by digi-led.pl
...Copyright © 2010-2013, Ekipa openrouter.info