Dzisiaj jest 23 wrz 2018, 16:23

Strefa czasowa UTC+1godz. [letni]




Nowy temat Odpowiedz w temacie  [ Posty: 293 ]  Przejdź na stronę Poprzednia  1 ... 7, 8, 9, 10, 11, 12, 13 ... 15  Następna
Autor Wiadomość
 Tytuł: Re: dwr-960 LTE
Post: 28 mar 2018, 10:01 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 317
Soft z poprzedniego posta:

....................
Starting kernel @80000000...
[ 0.000000] Linux version 4.9.86 (krolik@krolik-T420) (gcc version 7.3.0 (Ope nWrt GCC 7.3.0 r6443+3-d88e928) ) #0 Sun Mar 25 17:56:29 2018
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is D-Link DWR-960
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs 2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00020630
[ 0.000000] Readback ErrCtl register=00020630
[ 0.000000] Memory: 60428K/65536K available (3126K kernel code, 158K rwdata, 756K rodata, 176K init, 217K bss, 5108K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_n s: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_i dle_ns: 6590553264 ns
[ 0.000009] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 74051 15902ns
[ 0.015461] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.080614] pid_max: default: 32768 minimum: 301
[ 0.089896] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.102948] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.122881] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns
[ 0.142361] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.154507] pinctrl core: initialized pinctrl subsystem
[ 0.165443] NET: Registered protocol family 16
[ 0.195685] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.206713] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.219253] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.230235] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.242756] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.253735] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.266236] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.277031] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.293064] clocksource: Switched to clocksource systick
[ 0.304691] NET: Registered protocol family 2
[ 0.314102] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.327872] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.340469] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.353192] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.364723] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.377400] NET: Registered protocol family 1
[ 0.388216] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.400854] Crashlog allocated RAM at address 0x3f00000
[ 0.412292] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.432528] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.444019] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.472066] io scheduler noop registered
[ 0.479766] io scheduler deadline registered (default)
[ 0.490141] ralink-usb-phy usbphy: invalid resource
[ 0.500220] gpio-export gpio_export: 1 gpio(s) exported
[ 0.510707] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.524269] console [ttyS0] disabled
[ 0.531257] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.551033] console [ttyS0] enabled
[ 0.551033] console [ttyS0] enabled
[ 0.564810] bootconsole [early0] disabled
[ 0.564810] bootconsole [early0] disabled
[ 0.584898] spi spi0.0: force spi mode3
[ 0.603956] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.613378] 3 ofpart partitions found on MTD device spi0.0
[ 0.624311] Creating 3 MTD partitions on "spi0.0":
[ 0.633869] 0x000000000000-0x000000010000 : "jboot"
[ 0.645159] 0x000000010000-0x000000ff0000 : "firmware"
[ 0.657433] 2 jimage-fw partitions found on MTD device firmware
[ 0.669310] 0x000000010000-0x00000015cc15 : "kernel"
[ 0.680861] 0x00000015cc15-0x000000ff0000 : "rootfs"
[ 0.692516] mtd: device 3 (rootfs) set to be root filesystem
[ 0.704353] 1 squashfs-split partitions found on MTD device rootfs
[ 0.716725] 0x000000363000-0x000000ff0000 : "rootfs_data"
[ 0.729002] 0x000000ff0000-0x000001000000 : "config"
[ 0.741244] libphy: Fixed MDIO Bus: probed
[ 0.753065] PHY 0x0: 0x3A2940D
[ 0.759381] PHY 0x1: 0x3A2940D
[ 0.765696] PHY 0x2: 0x3A2940D
[ 0.771994] PHY 0x3: 0x3A2940D
[ 0.778306] PHY 0x4: 0x3A2940D
[ 0.784619] PHY 0x5: 0xFFFFFFFF
[ 0.791091] PHY 0x6: 0xFFFFFFFF
[ 0.797576] PHY 0x7: 0x4DD072
[ 0.803717] PHY 0x8: 0xFFFFFFFF
[ 0.810189] PHY 0x9: 0xFFFFFFFF
[ 0.816674] PHY 0xA: 0xFFFFFFFF
[ 0.823160] PHY 0xB: 0xFFFFFFFF
[ 0.829632] PHY 0xC: 0xFFFFFFFF
[ 0.836117] PHY 0xD: 0xFFFFFFFF
[ 0.842589] PHY 0xE: 0xFFFFFFFF
[ 0.849075] PHY 0xF: 0xFFFFFFFF
[ 0.855561] PHY 0x10: 0xFFFFFFFF
[ 0.862206] PHY 0x11: 0xFFFFFFFF
[ 0.868865] PHY 0x12: 0xFFFFFFFF
[ 0.875524] PHY 0x13: 0xFFFFFFFF
[ 0.882169] PHY 0x14: 0xFFFFFFFF
[ 0.888835] PHY 0x15: 0xFFFFFFFF
[ 0.895493] PHY 0x16: 0xFFFFFFFF
[ 0.902138] PHY 0x17: 0xFFFFFFFF
[ 0.908796] PHY 0x18: 0xFFFFFFFF
[ 0.915455] PHY 0x19: 0xFFFFFFFF
[ 0.922100] PHY 0x1A: 0xFFFFFFFF
[ 0.928758] PHY 0x1B: 0xFFFFFFFF
[ 0.935417] PHY 0x1C: 0xFFFFFFFF
[ 0.942062] PHY 0x1D: 0xFFFFFFFF
[ 0.948720] PHY 0x1E: 0xFFFFFFFF
[ 0.955380] PHY 0x1F: 0xFFFFFFFF
[ 0.961998] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 2 link u p (100Mbps/Full duplex)
[ 0.980227] mtk_soc_eth 10100000.ethernet: generated random MAC address c2:89 :1e:1c:0b:84
[ 0.996689] libphy: mdio: probed
[ 1.004041] mtk_soc_eth 10100000.ethernet: connected port 4 to PHY at mdio-bu s:04 [uid=03a2940d, driver=Generic PHY]
[ 1.025158] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 1.037670] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0 100000, irq 5
[ 1.054659] rt2880_wdt 10000120.watchdog: Initialized
[ 1.065796] NET: Registered protocol family 10
[ 1.077700] NET: Registered protocol family 17
[ 1.086685] 8021q: 802.1Q VLAN Support v1.8
[ 1.103602] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.118632] Freeing unused kernel memory: 176K
[ 1.127513] This architecture does not have kernel memory protection.
[ 1.837746] init: Console is alive
[ 1.844839] init: - watchdog -
[ 2.413020] random: fast init done
[ 2.927379] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.071603] usbcore: registered new interface driver usbfs
[ 3.082713] usbcore: registered new interface driver hub
[ 3.093424] usbcore: registered new device driver usb
[ 3.109099] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.123892] ehci-platform: EHCI generic platform driver
[ 3.144671] phy phy-usbphy.0: remote usb device wakeup disabled
[ 3.156478] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 3.165360] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 3.176849] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 3.192751] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 3.214726] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 3.228211] hub 1-0:1.0: USB hub found
[ 3.236082] hub 1-0:1.0: 1 port detected
[ 3.246991] kmodloader: done loading kernel modules from /etc/modules-boot.d/ *
[ 3.265751] init: - preinit -
[ 4.441113] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4.452810] 8021q: adding VLAN 0 to HW filter on device eth0
[ 4.464561] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 4.905447] mtk_soc_eth 10100000.ethernet eth0: port 4 link up (1000Mbps/Full duplex)
[ 5.845533] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 5.895497] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 6.030769] procd: - early -
[ 6.036698] procd: - watchdog -
[ 6.383660] mtk_soc_eth 10100000.ethernet eth0: port 4 link down
[ 6.431074] procd: - watchdog -
[ 6.437661] procd: - ubus -
[ 6.657661] procd: - init -
Please press Enter to activate this console.
[ 6.995692] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.014695] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.038418] usbcore: registered new interface driver cdc_wdm
[ 7.051846] Loading modules backported from Linux version wt-2017-11-01-0-gfe 248fc2c180
[ 7.067854] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 7.085376] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.105012] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 7.180189] xt_time: kernel timezone is -0000
[ 7.350006] PPP generic driver version 2.4.2
[ 7.361383] NET: Registered protocol family 24
[ 7.372820] usbcore: registered new interface driver qmi_wwan
[ 7.414135] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEP ROM data from 'soc_wmac.eeprom'.
[ 7.434114] rt2800_wmac 10180000.wmac: Direct firmware load for soc_wmac.eepr om failed with error -2
[ 7.452337] rt2800_wmac 10180000.wmac: Falling back to user helper
[ 7.581266] firmware soc_wmac.eeprom: firmware_loading_store: map pages faile d
[ 7.595887] ieee80211 phy0: rt2x00lib_request_eeprom_file: Error - Failed to request EEPROM.
[ 7.612777] rt2800_wmac: probe of 10180000.wmac failed with error -11
[ 7.651272] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 11.289188] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 14.699286] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 14.745034] jffs2_build_filesystem(): unlocking the mtd device... [ 14.8008 61] done.
[ 14.804728] jffs2_build_filesystem(): erasing all blocks after the end marker ... [ 19.861412] 8021q: adding VLAN 0 to HW filter on device eth0
[ 19.873249] mtk_soc_eth 10100000.ethernet eth0: port 4 link up (1000Mbps/Full duplex)
[ 19.940651] device eth0 entered promiscuous mode
[ 20.053785] br-lan: port 1(eth0.1) entered blocking state
[ 20.064629] br-lan: port 1(eth0.1) entered disabled state
[ 20.075829] device eth0.1 entered promiscuous mode
[ 20.169300] br-lan: port 1(eth0.1) entered blocking state
[ 20.180096] br-lan: port 1(eth0.1) entered forwarding state
[ 20.191404] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 20.889337] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 100.075779] mtk_soc_eth 10100000.ethernet eth0: port 2 link down
[ 100.088497] br-lan: port 1(eth0.1) entered disabled state
[ 104.112903] mtk_soc_eth 10100000.ethernet eth0: port 1 link up (100Mbps/Full duplex)
[ 104.128771] br-lan: port 1(eth0.1) entered blocking state
[ 104.139557] br-lan: port 1(eth0.1) entered forwarding state
[ 113.738117] mtk_soc_eth 10100000.ethernet eth0: port 1 link down
[ 113.750841] br-lan: port 1(eth0.1) entered disabled state
[ 117.941505] mtk_soc_eth 10100000.ethernet eth0: port 3 link up (100Mbps/Full duplex)
[ 117.957392] br-lan: port 1(eth0.1) entered blocking state
[ 117.968183] br-lan: port 1(eth0.1) entered forwarding state
[ 121.507977] mtk_soc_eth 10100000.ethernet eth0: port 3 link down
[ 121.534167] br-lan: port 1(eth0.1) entered disabled state
[ 121.689157] random: crng init done


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 28 mar 2018, 10:14 
Offline
Użytkownik

Rejestracja: 3 mar 2018, 09:59
Posty: 73
Pomysł się sprawdził, gigabit powinien zacząć działać jako WAN.

https://www.dropbox.com/s/y4qs27rwwkmiy ... y.bin?dl=0
https://www.dropbox.com/s/3gp6wdet0wnj3 ... e.bin?dl=0

Daj bootlog proszę.


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 28 mar 2018, 14:00 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 317
Wgrany najnowszy soft. Oto logi:

Starting kernel @80000000...
[ 0.000000] Linux version 4.9.86 (krolik@krolik-T420) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r6443+3-d88e928) ) #0 Sun Mar 25 17:56:29 2018
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is D-Link DWR-960
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000f30
[ 0.000000] Readback ErrCtl register=00000f30
[ 0.000000] Memory: 60428K/65536K available (3126K kernel code, 158K rwdata, 756K rodata, 176K init, 217K bss, 5108K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015461] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.080618] pid_max: default: 32768 minimum: 301
[ 0.089900] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.102952] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.122885] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.142366] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.154511] pinctrl core: initialized pinctrl subsystem
[ 0.165450] NET: Registered protocol family 16
[ 0.195688] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.206717] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.219257] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.230238] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.242760] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.253738] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.266240] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.277035] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.293068] clocksource: Switched to clocksource systick
[ 0.304695] NET: Registered protocol family 2
[ 0.314102] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.327872] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.340471] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.353194] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.364724] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.377400] NET: Registered protocol family 1
[ 0.388216] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.400854] Crashlog allocated RAM at address 0x3f00000
[ 0.412292] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.432527] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.444019] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.472066] io scheduler noop registered
[ 0.479767] io scheduler deadline registered (default)
[ 0.490142] ralink-usb-phy usbphy: invalid resource
[ 0.500220] gpio-export gpio_export: 1 gpio(s) exported
[ 0.510707] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.524269] console [ttyS0] disabled
[ 0.531256] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.551033] console [ttyS0] enabled
[ 0.551033] console [ttyS0] enabled
[ 0.564810] bootconsole [early0] disabled
[ 0.564810] bootconsole [early0] disabled
[ 0.584897] spi spi0.0: force spi mode3
[ 0.603968] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.613390] 3 ofpart partitions found on MTD device spi0.0
[ 0.624323] Creating 3 MTD partitions on "spi0.0":
[ 0.633878] 0x000000000000-0x000000010000 : "jboot"
[ 0.645167] 0x000000010000-0x000000ff0000 : "firmware"
[ 0.657443] 2 jimage-fw partitions found on MTD device firmware
[ 0.669319] 0x000000010000-0x00000015cc1b : "kernel"
[ 0.680873] 0x00000015cc1b-0x000000ff0000 : "rootfs"
[ 0.692531] mtd: device 3 (rootfs) set to be root filesystem
[ 0.704368] 1 squashfs-split partitions found on MTD device rootfs
[ 0.716740] 0x000000363000-0x000000ff0000 : "rootfs_data"
[ 0.729018] 0x000000ff0000-0x000001000000 : "config"
[ 0.741259] libphy: Fixed MDIO Bus: probed
[ 0.753077] PHY 0x0: 0x3A2940D
[ 0.759392] PHY 0x1: 0x3A2940D
[ 0.765706] PHY 0x2: 0x3A2940D
[ 0.772006] PHY 0x3: 0x3A2940D
[ 0.778318] PHY 0x4: 0x3A2940D
[ 0.784630] PHY 0x5: 0xFFFFFFFF
[ 0.791102] PHY 0x6: 0xFFFFFFFF
[ 0.797588] PHY 0x7: 0x4DD072
[ 0.803726] PHY 0x8: 0xFFFFFFFF
[ 0.810198] PHY 0x9: 0xFFFFFFFF
[ 0.816684] PHY 0xA: 0xFFFFFFFF
[ 0.823170] PHY 0xB: 0xFFFFFFFF
[ 0.829641] PHY 0xC: 0xFFFFFFFF
[ 0.836127] PHY 0xD: 0xFFFFFFFF
[ 0.842599] PHY 0xE: 0xFFFFFFFF
[ 0.849085] PHY 0xF: 0xFFFFFFFF
[ 0.855571] PHY 0x10: 0xFFFFFFFF
[ 0.862216] PHY 0x11: 0xFFFFFFFF
[ 0.868875] PHY 0x12: 0xFFFFFFFF
[ 0.875534] PHY 0x13: 0xFFFFFFFF
[ 0.882179] PHY 0x14: 0xFFFFFFFF
[ 0.888846] PHY 0x15: 0xFFFFFFFF
[ 0.895505] PHY 0x16: 0xFFFFFFFF
[ 0.902150] PHY 0x17: 0xFFFFFFFF
[ 0.908808] PHY 0x18: 0xFFFFFFFF
[ 0.915467] PHY 0x19: 0xFFFFFFFF
[ 0.922112] PHY 0x1A: 0xFFFFFFFF
[ 0.928771] PHY 0x1B: 0xFFFFFFFF
[ 0.935430] PHY 0x1C: 0xFFFFFFFF
[ 0.942075] PHY 0x1D: 0xFFFFFFFF
[ 0.948734] PHY 0x1E: 0xFFFFFFFF
[ 0.955393] PHY 0x1F: 0xFFFFFFFF
[ 0.962010] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 2 link up (100Mbps/Full duplex)
[ 0.980239] mtk_soc_eth 10100000.ethernet: generated random MAC address 56:f5:eb:9d:f2:73
[ 0.996703] libphy: mdio: probed
[ 1.037658] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 1.050219] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 1.067211] rt2880_wdt 10000120.watchdog: Initialized
[ 1.078342] NET: Registered protocol family 10
[ 1.090123] NET: Registered protocol family 17
[ 1.099107] 8021q: 802.1Q VLAN Support v1.8
[ 1.115949] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.131019] Freeing unused kernel memory: 176K
[ 1.139901] This architecture does not have kernel memory protection.
[ 1.849935] init: Console is alive
[ 1.856929] init: - watchdog -
[ 2.377266] random: fast init done
[ 2.939650] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.084642] usbcore: registered new interface driver usbfs
[ 3.095751] usbcore: registered new interface driver hub
[ 3.106460] usbcore: registered new device driver usb
[ 3.122195] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.136905] ehci-platform: EHCI generic platform driver
[ 3.157690] phy phy-usbphy.0: remote usb device wakeup disabled
[ 3.169498] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 3.178382] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 3.189870] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 3.205767] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 3.228150] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 3.241635] hub 1-0:1.0: USB hub found
[ 3.249507] hub 1-0:1.0: 1 port detected
[ 3.260400] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.279158] init: - preinit -
[ 4.454837] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4.466534] 8021q: adding VLAN 0 to HW filter on device eth0
[ 4.478082] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.849204] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 5.899250] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 6.033954] procd: - early -
[ 6.040563] procd: - watchdog -
[ 6.427170] procd: - watchdog -
[ 6.433709] procd: - ubus -
[ 6.653708] procd: - init -
Please press Enter to activate this console.
[ 6.992283] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.011193] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.035167] usbcore: registered new interface driver cdc_wdm
[ 7.048421] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[ 7.064442] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 7.081969] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.101601] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 7.177697] xt_time: kernel timezone is -0000
[ 7.348300] PPP generic driver version 2.4.2
[ 7.359524] NET: Registered protocol family 24
[ 7.370967] usbcore: registered new interface driver qmi_wwan
[ 7.412037] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
[ 7.432003] rt2800_wmac 10180000.wmac: Direct firmware load for soc_wmac.eeprom failed with error -2
[ 7.450245] rt2800_wmac 10180000.wmac: Falling back to user helper
[ 7.579317] firmware soc_wmac.eeprom: firmware_loading_store: map pages failed
[ 7.594016] ieee80211 phy0: rt2x00lib_request_eeprom_file: Error - Failed to request EEPROM.
[ 7.610902] rt2800_wmac: probe of 10180000.wmac failed with error -11
[ 7.654246] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 11.232265] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 14.884989] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 14.923249] jffs2_build_filesystem(): unlocking the mtd device... [ 14.964567] done.
[ 14.968410] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 20.004609] 8021q: adding VLAN 0 to HW filter on device eth0
[ 20.083337] device eth0 entered promiscuous mode
[ 20.132184] br-lan: port 1(eth0.1) entered blocking state
[ 20.143033] br-lan: port 1(eth0.1) entered disabled state
[ 20.154242] device eth0.1 entered promiscuous mode
[ 20.299994] br-lan: port 1(eth0.1) entered blocking state
[ 20.310823] br-lan: port 1(eth0.1) entered forwarding state
[ 20.322154] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 21.042476] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready



Port 1Gbit nie pobiera adresu


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 28 mar 2018, 14:58 
Offline
Użytkownik

Rejestracja: 3 mar 2018, 09:59
Posty: 73
Mam nadzieję, że teraz zobaczy phy:

https://www.dropbox.com/s/y4qs27rwwkmiy ... y.bin?dl=0
https://www.dropbox.com/s/3gp6wdet0wnj3 ... e.bin?dl=0


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 28 mar 2018, 16:47 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 317
Starting kernel @80000000...
[ 0.000000] Linux version 4.9.86 (krolik@krolik-T420) (gcc version 7.3.0 (Ope nWrt GCC 7.3.0 r6443+3-d88e928) ) #0 Sun Mar 25 17:56:29 2018
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is D-Link DWR-960
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs 2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00000f30
[ 0.000000] Readback ErrCtl register=00000f30
[ 0.000000] Memory: 60428K/65536K available (3126K kernel code, 158K rwdata, 756K rodata, 176K init, 217K bss, 5108K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_n s: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_i dle_ns: 6590553264 ns
[ 0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 74051 15902ns
[ 0.015461] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.080604] pid_max: default: 32768 minimum: 301
[ 0.089887] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.102938] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.122873] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns
[ 0.142352] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.154499] pinctrl core: initialized pinctrl subsystem
[ 0.165435] NET: Registered protocol family 16
[ 0.195680] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.206707] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.219246] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.230228] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.242749] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.253727] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.266228] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.277023] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.293056] clocksource: Switched to clocksource systick
[ 0.304683] NET: Registered protocol family 2
[ 0.314093] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.327864] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.340461] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.353185] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.364715] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.377392] NET: Registered protocol family 1
[ 0.388208] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.400846] Crashlog allocated RAM at address 0x3f00000
[ 0.412284] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.432519] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.444011] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.472054] io scheduler noop registered
[ 0.479755] io scheduler deadline registered (default)
[ 0.490130] ralink-usb-phy usbphy: invalid resource
[ 0.500208] gpio-export gpio_export: 1 gpio(s) exported
[ 0.510696] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.524257] console [ttyS0] disabled
[ 0.531244] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.551021] console [ttyS0] enabled
[ 0.551021] console [ttyS0] enabled
[ 0.564798] bootconsole [early0] disabled
[ 0.564798] bootconsole [early0] disabled
[ 0.584885] spi spi0.0: force spi mode3
[ 0.603955] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.613378] 3 ofpart partitions found on MTD device spi0.0
[ 0.624312] Creating 3 MTD partitions on "spi0.0":
[ 0.633870] 0x000000000000-0x000000010000 : "jboot"
[ 0.645158] 0x000000010000-0x000000ff0000 : "firmware"
[ 0.657432] 2 jimage-fw partitions found on MTD device firmware
[ 0.669311] 0x000000010000-0x00000015cc1b : "kernel"
[ 0.680863] 0x00000015cc1b-0x000000ff0000 : "rootfs"
[ 0.692519] mtd: device 3 (rootfs) set to be root filesystem
[ 0.704356] 1 squashfs-split partitions found on MTD device rootfs
[ 0.716728] 0x000000363000-0x000000ff0000 : "rootfs_data"
[ 0.729006] 0x000000ff0000-0x000001000000 : "config"
[ 0.741247] libphy: Fixed MDIO Bus: probed
[ 0.753065] PHY 0x0: 0x3A2940D
[ 0.759382] PHY 0x1: 0x3A2940D
[ 0.765696] PHY 0x2: 0x3A2940D
[ 0.771996] PHY 0x3: 0x3A2940D
[ 0.778308] PHY 0x4: 0x3A2940D
[ 0.784623] PHY 0x5: 0xFFFFFFFF
[ 0.791094] PHY 0x6: 0xFFFFFFFF
[ 0.797579] PHY 0x7: 0x4DD072
[ 0.803719] PHY 0x8: 0xFFFFFFFF
[ 0.810190] PHY 0x9: 0xFFFFFFFF
[ 0.816676] PHY 0xA: 0xFFFFFFFF
[ 0.823162] PHY 0xB: 0xFFFFFFFF
[ 0.829634] PHY 0xC: 0xFFFFFFFF
[ 0.836120] PHY 0xD: 0xFFFFFFFF
[ 0.842591] PHY 0xE: 0xFFFFFFFF
[ 0.849078] PHY 0xF: 0xFFFFFFFF
[ 0.855566] PHY 0x10: 0xFFFFFFFF
[ 0.862211] PHY 0x11: 0xFFFFFFFF
[ 0.868870] PHY 0x12: 0xFFFFFFFF
[ 0.875529] PHY 0x13: 0xFFFFFFFF
[ 0.882175] PHY 0x14: 0xFFFFFFFF
[ 0.888841] PHY 0x15: 0xFFFFFFFF
[ 0.895500] PHY 0x16: 0xFFFFFFFF
[ 0.902145] PHY 0x17: 0xFFFFFFFF
[ 0.908804] PHY 0x18: 0xFFFFFFFF
[ 0.915463] PHY 0x19: 0xFFFFFFFF
[ 0.922109] PHY 0x1A: 0xFFFFFFFF
[ 0.928767] PHY 0x1B: 0xFFFFFFFF
[ 0.935426] PHY 0x1C: 0xFFFFFFFF
[ 0.942071] PHY 0x1D: 0xFFFFFFFF
[ 0.948729] PHY 0x1E: 0xFFFFFFFF
[ 0.955389] PHY 0x1F: 0xFFFFFFFF
[ 0.962007] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 2 link u p (100Mbps/Full duplex)
[ 0.980236] mtk_soc_eth 10100000.ethernet: generated random MAC address ea:d1 :44:46:45:67
[ 0.996699] libphy: mdio: probed
[ 1.037652] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 1.050211] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0 100000, irq 5
[ 1.067205] rt2880_wdt 10000120.watchdog: Initialized
[ 1.078337] NET: Registered protocol family 10
[ 1.090118] NET: Registered protocol family 17
[ 1.099102] 8021q: 802.1Q VLAN Support v1.8
[ 1.115944] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.131014] Freeing unused kernel memory: 176K
[ 1.139897] This architecture does not have kernel memory protection.
[ 1.849705] init: Console is alive
[ 1.856703] init: - watchdog -
[ 2.387258] random: fast init done
[ 2.939104] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.084074] usbcore: registered new interface driver usbfs
[ 3.095183] usbcore: registered new interface driver hub
[ 3.105893] usbcore: registered new device driver usb
[ 3.121627] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.136350] ehci-platform: EHCI generic platform driver
[ 3.157136] phy phy-usbphy.0: remote usb device wakeup disabled
[ 3.168947] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 3.177831] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 3.189320] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 3.205217] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 3.227779] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 3.241267] hub 1-0:1.0: USB hub found
[ 3.249140] hub 1-0:1.0: 1 port detected
[ 3.260033] kmodloader: done loading kernel modules from /etc/modules-boot.d/ *
[ 3.278793] init: - preinit -
[ 4.454806] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4.466504] 8021q: adding VLAN 0 to HW filter on device eth0
[ 4.478053] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.848183] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 5.898275] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 6.033015] procd: - early -
[ 6.039620] procd: - watchdog -
[ 6.426274] procd: - watchdog -
[ 6.432909] procd: - ubus -
[ 6.652406] procd: - init -
Please press Enter to activate this console.
[ 6.990160] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.009105] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.032699] usbcore: registered new interface driver cdc_wdm
[ 7.046099] Loading modules backported from Linux version wt-2017-11-01-0-gfe 248fc2c180
[ 7.062119] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 7.079611] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.099229] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 7.174296] xt_time: kernel timezone is -0000
[ 7.344250] PPP generic driver version 2.4.2
[ 7.355581] NET: Registered protocol family 24
[ 7.366989] usbcore: registered new interface driver qmi_wwan
[ 7.407900] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEP ROM data from 'soc_wmac.eeprom'.
[ 7.427878] rt2800_wmac 10180000.wmac: Direct firmware load for soc_wmac.eepr om failed with error -2
[ 7.446108] rt2800_wmac 10180000.wmac: Falling back to user helper
[ 7.574985] firmware soc_wmac.eeprom: firmware_loading_store: map pages faile d
[ 7.589589] ieee80211 phy0: rt2x00lib_request_eeprom_file: Error - Failed to request EEPROM.
[ 7.606476] rt2800_wmac: probe of 10180000.wmac failed with error -11
[ 7.645097] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 7.854453] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 14.612619] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 14.660609] jffs2_build_filesystem(): unlocking the mtd device... [ 14.7197 73] done.
[ 14.723617] jffs2_build_filesystem(): erasing all blocks after the end marker ... [ 19.852479] 8021q: adding VLAN 0 to HW filter on device eth0
[ 19.917136] device eth0 entered promiscuous mode
[ 20.031167] br-lan: port 1(eth0.1) entered blocking state
[ 20.042011] br-lan: port 1(eth0.1) entered disabled state
[ 20.053214] device eth0.1 entered promiscuous mode
[ 20.144516] br-lan: port 1(eth0.1) entered blocking state
[ 20.155339] br-lan: port 1(eth0.1) entered forwarding state
[ 20.166655] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 20.860351] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 28 mar 2018, 21:59 
Offline
Użytkownik

Rejestracja: 3 mar 2018, 09:59
Posty: 73
Cezary, potrzebuję rady. Było:

&ethernet {
   status = "okay";
   pinctrl-names = "default";
   pinctrl-0 = <&rgmii1_pins &mdio_pins &ephy_pins>;
   mediatek,portmap = "llllw";

   port@4 {
      status = "okay";
      phy-mode = "rgmii";
      phy-handle = <&phy7>;
   };

   mdio-bus {
      status = "okay";

      phy7: ethernet-phy@7 {
         reg = <7>;
         phy-mode = "rgmii";
      };

   };
};


oraz

&ethernet {
   status = "okay";
   pinctrl-names = "default";
   pinctrl-0 = <&rgmii1_pins &mdio_pins &ephy_pins>;
   mediatek,portmap = "llllw";

   port@4 {
      status = "okay";
      phy-mode = "rgmii";
      phy-handle = <&phy4>;
   };

   mdio-bus {
      status = "okay";

      phy4: ethernet-phy@7 {
         reg = <7>;
         phy-mode = "rgmii";
      };

   };
};


i zero oznak życia od PHY.

Ewidentnie siedzi pod adresem "7":
[ 0.753065] PHY 0x0: 0x3A2940D
[ 0.759382] PHY 0x1: 0x3A2940D
[ 0.765696] PHY 0x2: 0x3A2940D
[ 0.771996] PHY 0x3: 0x3A2940D
[ 0.778308] PHY 0x4: 0x3A2940D
[ 0.784623] PHY 0x5: 0xFFFFFFFF
[ 0.791094] PHY 0x6: 0xFFFFFFFF
[ 0.797579] PHY 0x7: 0x4DD072
[ 0.803719] PHY 0x8: 0xFFFFFFFF


W pozostałych dtb od innych ramipsów nie znalazłem pomocy.
Masz jakiś pomysł co robię źle?


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 28 mar 2018, 23:11 
Offline
Administrator
Awatar użytkownika

Rejestracja: 10 kwie 2010, 00:28
Posty: 13263
Lokalizacja: Warszawa
A to nie jest kwestia tego że w driverze nie ma nic o porcie 7?

_________________
http://eko.one.pl - prawie wszystko o OpenWrt


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 29 mar 2018, 06:56 
Offline
Administrator
Awatar użytkownika

Rejestracja: 10 kwie 2010, 00:28
Posty: 13263
Lokalizacja: Warszawa
PS. Myślę że powinieneś wysłać to do repo. Szkoda czasu, a zdarzały się już takie urządzenia z niepełnym wsparciem.

_________________
http://eko.one.pl - prawie wszystko o OpenWrt


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 29 mar 2018, 07:20 
Offline
Użytkownik

Rejestracja: 3 mar 2018, 09:59
Posty: 73
@smereka

https://www.dropbox.com/s/y4qs27rwwkmiy ... y.bin?dl=0
https://www.dropbox.com/s/3gp6wdet0wnj3 ... e.bin?dl=0



@Obsy

Ostatnia próba z takim wariantem:

&ethernet {
   status = "okay";
   pinctrl-names = "default";
   pinctrl-0 = <&rgmii1_pins &mdio_pins &ephy_pins>;
   mediatek,portmap = "llllw";

   port@4 {
      status = "okay";
      phy-mode = "rgmii";
      phy-handle = <&phy4>;
   };

   mdio-bus {
      status = "okay";

      phy4: ethernet-phy@4 {
         reg = <7>;
         phy-mode = "rgmii";
      };

   };
};


Jak to nie zadziała, to jeszcze się M. Kresina zapytam o pomoc.

Zostanie sprawdzenie LEDek do końca i wsparcie dla LTE. Najwyżej pójdzie do repo bez wifi 5GHz i gigabita.

EDIT:

   _port = of_get_property(phy_node, "reg", NULL);

   if (!_port || (be32_to_cpu(*_port) >= 0x20)) {
      pr_err("%s: invalid port id\n", phy_node->name);
      return -EINVAL;
   }


Driver powinien spokojnie łyknąć ten reg = <7>. :/

EDIT2:

Driver w ogóle nie zgłasza próby podłączenia do phy w logu. To mnie dziwi najbardziej.


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 29 mar 2018, 07:52 
Offline
Administrator
Awatar użytkownika

Rejestracja: 10 kwie 2010, 00:28
Posty: 13263
Lokalizacja: Warszawa
Modem LTE nie sprawia problemu, tak samo jak dodaliście dla C1/C3 to po prostu kolejny wpis dla qmi. Ten ethernet jest zadziwiający.

_________________
http://eko.one.pl - prawie wszystko o OpenWrt


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 29 mar 2018, 08:00 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 317
Jeszcze mnie przy routerze nie ma. W ogóle to wczoraj zapomniałem go ze sobą zabrać. Dzisiaj wezmę i wystawię wam jeśli taka jest potrzeba.

Dodam, że na OFW ten niemrawy port też sprawia problemy. Owszem działa ale po kilkudziesięciu sekundach. Strasznie długo pobiera na nim IP. Ale jak już działa to na XP pokazuje tylko 100Mbit. Karta w lapku oczywiście 1Gbit. Jak wpinam lapka do wdr3600 czy innego switcha to mam normalnie 1Gbit.


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 29 mar 2018, 08:02 
Offline
Użytkownik

Rejestracja: 3 mar 2018, 09:59
Posty: 73
obsy pisze:
Modem LTE nie sprawia problemu, tak samo jak dodaliście dla C1/C3 to po prostu kolejny wpis dla qmi. Ten ethernet jest zadziwiający.


Oglądałem pozostałe dts-y dla ramipsów. W żadnym nie widziałem analogicznej sytuacji.

@smereka

Nie wiem czy przed świętami będę miał kiedy siedzieć nad tym wieczorem, także póki co zostańmy przy trybie korespondencyjnym. ;)

Jak dzisiejszy soft nie pomoże, to trzeba się będzie mocno zastanowić o co chodzi.


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 29 mar 2018, 10:03 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 317
Starting kernel @80000000...
[ 0.000000] Linux version 4.9.86 (krolik@krolik-T420) (gcc version 7.3.0 (Ope nWrt GCC 7.3.0 r6443+3-d88e928) ) #0 Sun Mar 25 17:56:29 2018
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is D-Link DWR-960
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs 2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=0007efb0
[ 0.000000] Readback ErrCtl register=0007efb0
[ 0.000000] Memory: 60428K/65536K available (3126K kernel code, 158K rwdata, 756K rodata, 176K init, 217K bss, 5108K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_n s: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_i dle_ns: 6590553264 ns
[ 0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 74051 15902ns
[ 0.015461] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.080608] pid_max: default: 32768 minimum: 301
[ 0.089890] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.102942] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.122881] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns
[ 0.142362] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.154508] pinctrl core: initialized pinctrl subsystem
[ 0.165445] NET: Registered protocol family 16
[ 0.195686] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.206715] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.219254] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.230236] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.242757] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.253735] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.266237] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.277032] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.293068] clocksource: Switched to clocksource systick
[ 0.304693] NET: Registered protocol family 2
[ 0.314103] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.327874] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.340471] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.353195] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.364725] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.377402] NET: Registered protocol family 1
[ 0.388218] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.400859] Crashlog allocated RAM at address 0x3f00000
[ 0.412298] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.432534] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.444025] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.472064] io scheduler noop registered
[ 0.479766] io scheduler deadline registered (default)
[ 0.490140] ralink-usb-phy usbphy: invalid resource
[ 0.500219] gpio-export gpio_export: 1 gpio(s) exported
[ 0.510707] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.524271] console [ttyS0] disabled
[ 0.531259] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.551035] console [ttyS0] enabled
[ 0.551035] console [ttyS0] enabled
[ 0.564811] bootconsole [early0] disabled
[ 0.564811] bootconsole [early0] disabled
[ 0.584894] spi spi0.0: force spi mode3
[ 0.603997] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.613419] 3 ofpart partitions found on MTD device spi0.0
[ 0.624351] Creating 3 MTD partitions on "spi0.0":
[ 0.633909] 0x000000000000-0x000000010000 : "jboot"
[ 0.645200] 0x000000010000-0x000000ff0000 : "firmware"
[ 0.657473] 2 jimage-fw partitions found on MTD device firmware
[ 0.669350] 0x000000010000-0x00000015cc97 : "kernel"
[ 0.680901] 0x00000015cc97-0x000000ff0000 : "rootfs"
[ 0.692557] mtd: device 3 (rootfs) set to be root filesystem
[ 0.704395] 1 squashfs-split partitions found on MTD device rootfs
[ 0.716768] 0x000000363000-0x000000ff0000 : "rootfs_data"
[ 0.729046] 0x000000ff0000-0x000001000000 : "config"
[ 0.741290] libphy: Fixed MDIO Bus: probed
[ 0.753124] PHY 0x0: 0x3A2940D
[ 0.759439] PHY 0x1: 0x3A2940D
[ 0.765754] PHY 0x2: 0x3A2940D
[ 0.772052] PHY 0x3: 0x3A2940D
[ 0.778365] PHY 0x4: 0x3A2940D
[ 0.784679] PHY 0x5: 0xFFFFFFFF
[ 0.791151] PHY 0x6: 0xFFFFFFFF
[ 0.797636] PHY 0x7: 0x4DD072
[ 0.803776] PHY 0x8: 0xFFFFFFFF
[ 0.810247] PHY 0x9: 0xFFFFFFFF
[ 0.816733] PHY 0xA: 0xFFFFFFFF
[ 0.823219] PHY 0xB: 0xFFFFFFFF
[ 0.829691] PHY 0xC: 0xFFFFFFFF
[ 0.836176] PHY 0xD: 0xFFFFFFFF
[ 0.842648] PHY 0xE: 0xFFFFFFFF
[ 0.849133] PHY 0xF: 0xFFFFFFFF
[ 0.855621] PHY 0x10: 0xFFFFFFFF
[ 0.862266] PHY 0x11: 0xFFFFFFFF
[ 0.868925] PHY 0x12: 0xFFFFFFFF
[ 0.875584] PHY 0x13: 0xFFFFFFFF
[ 0.882230] PHY 0x14: 0xFFFFFFFF
[ 0.888896] PHY 0x15: 0xFFFFFFFF
[ 0.895555] PHY 0x16: 0xFFFFFFFF
[ 0.902200] PHY 0x17: 0xFFFFFFFF
[ 0.908859] PHY 0x18: 0xFFFFFFFF
[ 0.915518] PHY 0x19: 0xFFFFFFFF
[ 0.922162] PHY 0x1A: 0xFFFFFFFF
[ 0.928820] PHY 0x1B: 0xFFFFFFFF
[ 0.935479] PHY 0x1C: 0xFFFFFFFF
[ 0.942124] PHY 0x1D: 0xFFFFFFFF
[ 0.948783] PHY 0x1E: 0xFFFFFFFF
[ 0.955442] PHY 0x1F: 0xFFFFFFFF
[ 0.962059] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 2 link u p (100Mbps/Full duplex)
[ 0.980287] mtk_soc_eth 10100000.ethernet: generated random MAC address 22:82 :a0:45:bc:b4
[ 0.996751] libphy: mdio: probed
[ 1.037685] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 1.050244] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0 100000, irq 5
[ 1.067237] rt2880_wdt 10000120.watchdog: Initialized
[ 1.078367] NET: Registered protocol family 10
[ 1.090145] NET: Registered protocol family 17
[ 1.099129] 8021q: 802.1Q VLAN Support v1.8
[ 1.115974] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.131044] Freeing unused kernel memory: 176K
[ 1.139926] This architecture does not have kernel memory protection.
[ 1.849745] init: Console is alive
[ 1.856740] init: - watchdog -
[ 2.377291] random: fast init done
[ 2.939027] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.084035] usbcore: registered new interface driver usbfs
[ 3.095143] usbcore: registered new interface driver hub
[ 3.105853] usbcore: registered new device driver usb
[ 3.121606] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.136300] ehci-platform: EHCI generic platform driver
[ 3.157088] phy phy-usbphy.0: remote usb device wakeup disabled
[ 3.168897] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 3.177781] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 3.189270] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 3.205167] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 3.227756] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 3.241246] hub 1-0:1.0: USB hub found
[ 3.249119] hub 1-0:1.0: 1 port detected
[ 3.260010] kmodloader: done loading kernel modules from /etc/modules-boot.d/ *
[ 3.278767] init: - preinit -
[ 4.453952] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4.465650] 8021q: adding VLAN 0 to HW filter on device eth0
[ 4.477191] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.848823] mount_root: jffs2 not ready yet, using temporary tmpfs overlay
[ 5.898889] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 6.033857] procd: - early -
[ 6.040465] procd: - watchdog -
[ 6.427349] procd: - watchdog -
[ 6.433874] procd: - ubus -
[ 6.653922] procd: - init -
Please press Enter to activate this console.
[ 6.991933] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.010841] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.034579] usbcore: registered new interface driver cdc_wdm
[ 7.047883] Loading modules backported from Linux version wt-2017-11-01-0-gfe 248fc2c180
[ 7.063906] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 7.081416] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.100940] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 7.176740] xt_time: kernel timezone is -0000
[ 7.346486] PPP generic driver version 2.4.2
[ 7.357706] NET: Registered protocol family 24
[ 7.369154] usbcore: registered new interface driver qmi_wwan
[ 7.410234] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEP ROM data from 'soc_wmac.eeprom'.
[ 7.430213] rt2800_wmac 10180000.wmac: Direct firmware load for soc_wmac.eepr om failed with error -2
[ 7.448444] rt2800_wmac 10180000.wmac: Falling back to user helper
[ 7.577177] firmware soc_wmac.eeprom: firmware_loading_store: map pages faile d
[ 7.591856] ieee80211 phy0: rt2x00lib_request_eeprom_file: Error - Failed to request EEPROM.
[ 7.608770] rt2800_wmac: probe of 10180000.wmac failed with error -11
[ 7.653739] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 7.775473] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 14.839629] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
[ 14.879631] jffs2_build_filesystem(): unlocking the mtd device... [ 14.9785 64] done.
[ 14.982410] jffs2_build_filesystem(): erasing all blocks after the end marker ... [ 19.830988] 8021q: adding VLAN 0 to HW filter on device eth0
[ 19.908227] device eth0 entered promiscuous mode
[ 19.952619] br-lan: port 1(eth0.1) entered blocking state
[ 19.963448] br-lan: port 1(eth0.1) entered disabled state
[ 19.974649] device eth0.1 entered promiscuous mode
[ 20.134107] br-lan: port 1(eth0.1) entered blocking state
[ 20.144935] br-lan: port 1(eth0.1) entered forwarding state
[ 20.156256] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 20.859542] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready


Tiszyna...


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 29 mar 2018, 12:40 
Offline
Użytkownik

Rejestracja: 3 mar 2018, 09:59
Posty: 73
No dobra. D-Link nie odezwał się w sprawie GPL. Czekam na odpowiedź M. Kresina. Zobaczymy co wyjdzie z tego gigabita w międzyczasie.

@smereka
Daj mu w pełni zbudować overlay i zrób mu reset. Sprawdzimy pozostałe rzeczy.
Czy ledki od lanu i wifi działają teraz dobrze?
Czy wifi 2.4G działa?
Czy MAC się zgadza?
Sysupgrade działa?


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 30 mar 2018, 10:10 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 317
@Krolik

1. Co znaczy w pełni zbudować overlay - podaj proszę instrukcję krok po kroku
2. Po włączeniu bez żadnych przewodów pali się tylko dioda "status". Po wpięciu przewodu do któregoś z portu LAN zapala się dioda "4G"
3. Nie wiem czy wifi działa. Jak możesz zrób mi proszę obraz z Luci to sprawdzę. Strasznie nie lubię grzebać w configach dlatego Luci to dla mnie wybawienie. Sam sobie nie doinstaluję bo WAN nie działa - jak zresztą wiesz.
4. MAC chyba dobre
5. Na ostatnim sofcie na którym był WAN jak dobrze pamiętam po wgraniu Luci nie chciało mi przyjmować sysupgrade.


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 30 mar 2018, 12:41 
Offline
Administrator
Awatar użytkownika

Rejestracja: 10 kwie 2010, 00:28
Posty: 13263
Lokalizacja: Warszawa
1. Flash, poczekaj kilka minut, reboot i masz
3.
uci set wireless.@wifi-device[0].disabled=0
uci commit wireless
wifi

_________________
http://eko.one.pl - prawie wszystko o OpenWrt


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 30 mar 2018, 12:49 
Offline
Użytkownik

Rejestracja: 3 mar 2018, 09:59
Posty: 73
1. Overlay sam się buduje przy pierwszym starcie, tylko trzeba mu dać czas. Jak status działa, to sygnalizuje jak jest gotowy.
2. 3. Postaram się przygotować obraz z luci i poprawie ledy.
4. Git
5. Możliwe, że podczas przejścia z obrazów Cezarego do moich. Zmieniła się nazwa urządzenia.

Możesz zrobić zdjęcie obudowy z przodu? Interesuje mnie rozkład ledek i ich opisów.


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 30 mar 2018, 14:23 
Offline
Użytkownik

Rejestracja: 10 lut 2011, 09:30
Posty: 317
Errata do poprzedniego posta:

Wpięcie przewodu do I portu nie zapala żadnej diody
Wpięcie przewodu do II portu zapala diodę 4G
Wpięcie przewodu do III portu zapala diodę 2G/3G
Wpięcie przewodu do IV - tego nie wiemy to stawia ostry protest od początku narodzin openwrt
Wpięcie przewodu do WAN nie zapala żadnej diody
Dioda signal strength miga na czerowo-pomarańczowo jak piszę coś w konsoli

Facjata pacjenta dodana do pierwszego posta

Cezary ta komenda do wifi wypluwa mi:

uci: Entry not found

Nie wiem czy o to chodzi z overlay. Zrobiłem mu firstboota. Odczekałem z 10 minut i znowu reboot. Oto logi:

CDG56CDL_0T3 Jboot B972
JRecovery Version R1.2 2016/11/15 14:11
spi device id: ef 40 18 0 0 (40180000)
SPI FLASH: W25Q128FV 16M
.
....................
Starting kernel @80000000...
[ 0.000000] Linux version 4.9.86 (krolik@krolik-T420) (gcc version 7.3.0 (Ope nWrt GCC 7.3.0 r6443+3-d88e928) ) #0 Sun Mar 25 17:56:29 2018
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is D-Link DWR-960
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 byt es
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pag es: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs 2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00004f20
[ 0.000000] Readback ErrCtl register=00004f20
[ 0.000000] Memory: 60428K/65536K available (3126K kernel code, 158K rwdata, 756K rodata, 176K init, 217K bss, 5108K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_n s: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_i dle_ns: 6590553264 ns
[ 0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 74051 15902ns
[ 0.015461] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.080608] pid_max: default: 32768 minimum: 301
[ 0.089891] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.102943] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.122881] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, ma x_idle_ns: 19112604462750000 ns
[ 0.142361] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.154508] pinctrl core: initialized pinctrl subsystem
[ 0.165444] NET: Registered protocol family 16
[ 0.195685] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.206715] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.219253] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.230235] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.242754] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.253733] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.266234] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.277029] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.293063] clocksource: Switched to clocksource systick
[ 0.304690] NET: Registered protocol family 2
[ 0.314099] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.327871] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.340468] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.353191] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.364723] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.377400] NET: Registered protocol family 1
[ 0.388217] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.400858] Crashlog allocated RAM at address 0x3f00000
[ 0.412298] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.432534] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.444024] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORIT Y) (c) 2001-2006 Red Hat, Inc.
[ 0.472060] io scheduler noop registered
[ 0.479760] io scheduler deadline registered (default)
[ 0.490135] ralink-usb-phy usbphy: invalid resource
[ 0.500215] gpio-export gpio_export: 1 gpio(s) exported
[ 0.510702] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.524266] console [ttyS0] disabled
[ 0.531255] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.551031] console [ttyS0] enabled
[ 0.551031] console [ttyS0] enabled
[ 0.564808] bootconsole [early0] disabled
[ 0.564808] bootconsole [early0] disabled
[ 0.584893] spi spi0.0: force spi mode3
[ 0.603936] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.613359] 3 ofpart partitions found on MTD device spi0.0
[ 0.624291] Creating 3 MTD partitions on "spi0.0":
[ 0.633847] 0x000000000000-0x000000010000 : "jboot"
[ 0.645134] 0x000000010000-0x000000ff0000 : "firmware"
[ 0.657407] 2 jimage-fw partitions found on MTD device firmware
[ 0.669284] 0x000000010000-0x00000015cc97 : "kernel"
[ 0.680835] 0x00000015cc97-0x000000ff0000 : "rootfs"
[ 0.692491] mtd: device 3 (rootfs) set to be root filesystem
[ 0.704330] 1 squashfs-split partitions found on MTD device rootfs
[ 0.716702] 0x000000363000-0x000000ff0000 : "rootfs_data"
[ 0.728980] 0x000000ff0000-0x000001000000 : "config"
[ 0.741224] libphy: Fixed MDIO Bus: probed
[ 0.753065] PHY 0x0: 0x3A2940D
[ 0.759380] PHY 0x1: 0x3A2940D
[ 0.765695] PHY 0x2: 0x3A2940D
[ 0.771994] PHY 0x3: 0x3A2940D
[ 0.778306] PHY 0x4: 0x3A2940D
[ 0.784619] PHY 0x5: 0xFFFFFFFF
[ 0.791091] PHY 0x6: 0xFFFFFFFF
[ 0.797576] PHY 0x7: 0x4DD072
[ 0.803715] PHY 0x8: 0xFFFFFFFF
[ 0.810187] PHY 0x9: 0xFFFFFFFF
[ 0.816673] PHY 0xA: 0xFFFFFFFF
[ 0.823158] PHY 0xB: 0xFFFFFFFF
[ 0.829630] PHY 0xC: 0xFFFFFFFF
[ 0.836116] PHY 0xD: 0xFFFFFFFF
[ 0.842588] PHY 0xE: 0xFFFFFFFF
[ 0.849074] PHY 0xF: 0xFFFFFFFF
[ 0.855562] PHY 0x10: 0xFFFFFFFF
[ 0.862207] PHY 0x11: 0xFFFFFFFF
[ 0.868865] PHY 0x12: 0xFFFFFFFF
[ 0.875524] PHY 0x13: 0xFFFFFFFF
[ 0.882169] PHY 0x14: 0xFFFFFFFF
[ 0.888835] PHY 0x15: 0xFFFFFFFF
[ 0.895494] PHY 0x16: 0xFFFFFFFF
[ 0.902139] PHY 0x17: 0xFFFFFFFF
[ 0.908798] PHY 0x18: 0xFFFFFFFF
[ 0.915456] PHY 0x19: 0xFFFFFFFF
[ 0.922101] PHY 0x1A: 0xFFFFFFFF
[ 0.928760] PHY 0x1B: 0xFFFFFFFF
[ 0.935419] PHY 0x1C: 0xFFFFFFFF
[ 0.942064] PHY 0x1D: 0xFFFFFFFF
[ 0.948723] PHY 0x1E: 0xFFFFFFFF
[ 0.955382] PHY 0x1F: 0xFFFFFFFF
[ 0.961999] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 0 link u p (100Mbps/Full duplex)
[ 0.980229] mtk_soc_eth 10100000.ethernet: generated random MAC address 06:13 :de:59:48:24
[ 0.996693] libphy: mdio: probed
[ 1.037645] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 1.050203] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0 100000, irq 5
[ 1.067193] rt2880_wdt 10000120.watchdog: Initialized
[ 1.078323] NET: Registered protocol family 10
[ 1.090101] NET: Registered protocol family 17
[ 1.099083] 8021q: 802.1Q VLAN Support v1.8
[ 1.115930] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.130998] Freeing unused kernel memory: 176K
[ 1.139879] This architecture does not have kernel memory protection.
[ 1.849802] init: Console is alive
[ 1.856798] init: - watchdog -
[ 2.387253] random: fast init done
[ 2.939169] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.084182] usbcore: registered new interface driver usbfs
[ 3.095292] usbcore: registered new interface driver hub
[ 3.106001] usbcore: registered new device driver usb
[ 3.121748] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.136446] ehci-platform: EHCI generic platform driver
[ 3.157244] phy phy-usbphy.0: remote usb device wakeup disabled
[ 3.169051] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 3.177934] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 3.189422] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 3.205320] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 3.227845] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 3.241337] hub 1-0:1.0: USB hub found
[ 3.249210] hub 1-0:1.0: 1 port detected
[ 3.260095] kmodloader: done loading kernel modules from /etc/modules-boot.d/ *
[ 3.278853] init: - preinit -
[ 4.455358] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4.467058] 8021q: adding VLAN 0 to HW filter on device eth0
[ 4.478607] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 5.853548] mount_root: no usable overlay filesystem found, using tmpfs overl ay
[ 5.904375] urandom-seed: Seed file not found (/etc/urandom.seed)
[ 6.039947] procd: - early -
[ 6.045781] procd: - watchdog -
[ 6.432214] procd: - watchdog -
[ 6.438810] procd: - ubus -
[ 6.658552] procd: - init -
Please press Enter to activate this console.
[ 6.995366] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.014370] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.038304] usbcore: registered new interface driver cdc_wdm
[ 7.051545] Loading modules backported from Linux version wt-2017-11-01-0-gfe 248fc2c180
[ 7.067575] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 7.085078] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.104531] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 7.180871] xt_time: kernel timezone is -0000
[ 7.351254] PPP generic driver version 2.4.2
[ 7.362559] NET: Registered protocol family 24
[ 7.373989] usbcore: registered new interface driver qmi_wwan
[ 7.415067] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEP ROM data from 'soc_wmac.eeprom'.
[ 7.435034] rt2800_wmac 10180000.wmac: Direct firmware load for soc_wmac.eepr om failed with error -2
[ 7.453276] rt2800_wmac 10180000.wmac: Falling back to user helper
[ 7.582057] firmware soc_wmac.eeprom: firmware_loading_store: map pages faile d
[ 7.596740] ieee80211 phy0: rt2x00lib_request_eeprom_file: Error - Failed to request EEPROM.
[ 7.613633] rt2800_wmac: probe of 10180000.wmac failed with error -11
[ 7.656433] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 11.224385] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 16.391588] jffs2: notice: (899) jffs2_build_xattr_subsystem: complete buildi ng xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 19.006170] 8021q: adding VLAN 0 to HW filter on device eth0
[ 19.054756] device eth0 entered promiscuous mode
[ 19.098566] br-lan: port 1(eth0.1) entered blocking state
[ 19.109418] br-lan: port 1(eth0.1) entered disabled state
[ 19.120619] device eth0.1 entered promiscuous mode
[ 19.216320] br-lan: port 1(eth0.1) entered blocking state
[ 19.227146] br-lan: port 1(eth0.1) entered forwarding state
[ 19.238579] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 20.004635] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 101.705800] random: crng init done
[ 254.428030] br-lan: port 1(eth0.1) entered disabled state
[ 254.456343] device eth0.1 left promiscuous mode
[ 254.465591] br-lan: port 1(eth0.1) entered disabled state
[ 254.486648] IPv6: ADDRCONF(NETDEV_UP): eth0.1: link is not ready
[ 254.778900] device eth0 left promiscuous mode
[ 256.314867] reboot: Restarting system

CDG56CDL_0T3 Jboot B972
JRecovery Version R1.2 2016/11/15 14:11
spi device id: ef 40 18 0 0 (40180000)
SPI FLASH: W25Q128FV 16M
.
....................
Starting kernel @80000000...
[ 0.000000] Linux version 4.9.86 (krolik@krolik-T420) (gcc version 7.3.0 (OpenWrt GCC 7.3.0 r6443+3-d88e928) ) #0 Sun Mar 25 17:56:29 2018
[ 0.000000] Board has DDR2
[ 0.000000] Analog PMU set to hw control
[ 0.000000] Digital PMU set to hw control
[ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc)
[ 0.000000] MIPS: machine is D-Link DWR-960
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 04000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
[ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff]
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256
[ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2
[ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes)
[ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
[ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Writing ErrCtl register=00004f21
[ 0.000000] Readback ErrCtl register=00004f21
[ 0.000000] Memory: 60428K/65536K available (3126K kernel code, 158K rwdata, 756K rodata, 176K init, 217K bss, 5108K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
[ 0.000000] NR_IRQS:256
[ 0.000000] CPU Clock: 580MHz
[ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns
[ 0.000000] systick: enable autosleep mode
[ 0.000000] systick: running - mult: 214748, shift: 32
[ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns
[ 0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns
[ 0.015461] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216)
[ 0.080621] pid_max: default: 32768 minimum: 301
[ 0.089904] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.102955] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.122893] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[ 0.142373] futex hash table entries: 256 (order: -1, 3072 bytes)
[ 0.154519] pinctrl core: initialized pinctrl subsystem
[ 0.165455] NET: Registered protocol family 16
[ 0.195694] rt2880_gpio 10000600.gpio: registering 24 gpios
[ 0.206722] rt2880_gpio 10000600.gpio: registering 24 irq handlers
[ 0.219262] rt2880_gpio 10000638.gpio: registering 16 gpios
[ 0.230244] rt2880_gpio 10000638.gpio: registering 16 irq handlers
[ 0.242765] rt2880_gpio 10000660.gpio: registering 32 gpios
[ 0.253742] rt2880_gpio 10000660.gpio: registering 32 irq handlers
[ 0.266245] rt2880_gpio 10000688.gpio: registering 1 gpios
[ 0.277041] rt2880_gpio 10000688.gpio: registering 1 irq handlers
[ 0.293075] clocksource: Switched to clocksource systick
[ 0.304700] NET: Registered protocol family 2
[ 0.314111] TCP established hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.327881] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
[ 0.340478] TCP: Hash tables configured (established 1024 bind 1024)
[ 0.353203] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.364732] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.377410] NET: Registered protocol family 1
[ 0.388225] rt-timer 10000100.timer: maximum frequency is 1220Hz
[ 0.400867] Crashlog allocated RAM at address 0x3f00000
[ 0.412305] workingset: timestamp_bits=30 max_order=14 bucket_order=0
[ 0.432542] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.444033] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.472072] io scheduler noop registered
[ 0.479772] io scheduler deadline registered (default)
[ 0.490147] ralink-usb-phy usbphy: invalid resource
[ 0.500227] gpio-export gpio_export: 1 gpio(s) exported
[ 0.510714] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[ 0.524278] console [ttyS0] disabled
[ 0.531267] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103
[ 0.551043] console [ttyS0] enabled
[ 0.551043] console [ttyS0] enabled
[ 0.564819] bootconsole [early0] disabled
[ 0.564819] bootconsole [early0] disabled
[ 0.584901] spi spi0.0: force spi mode3
[ 0.603948] m25p80 spi0.0: w25q128 (16384 Kbytes)
[ 0.613370] 3 ofpart partitions found on MTD device spi0.0
[ 0.624302] Creating 3 MTD partitions on "spi0.0":
[ 0.633858] 0x000000000000-0x000000010000 : "jboot"
[ 0.645150] 0x000000010000-0x000000ff0000 : "firmware"
[ 0.657423] 2 jimage-fw partitions found on MTD device firmware
[ 0.669300] 0x000000010000-0x00000015cc97 : "kernel"
[ 0.680851] 0x00000015cc97-0x000000ff0000 : "rootfs"
[ 0.692507] mtd: device 3 (rootfs) set to be root filesystem
[ 0.704346] 1 squashfs-split partitions found on MTD device rootfs
[ 0.716719] 0x000000363000-0x000000ff0000 : "rootfs_data"
[ 0.728997] 0x000000ff0000-0x000001000000 : "config"
[ 0.741240] libphy: Fixed MDIO Bus: probed
[ 0.753080] PHY 0x0: 0x3A2940D
[ 0.759395] PHY 0x1: 0x3A2940D
[ 0.765710] PHY 0x2: 0x3A2940D
[ 0.772008] PHY 0x3: 0x3A2940D
[ 0.778321] PHY 0x4: 0x3A2940D
[ 0.784635] PHY 0x5: 0xFFFFFFFF
[ 0.791107] PHY 0x6: 0xFFFFFFFF
[ 0.797592] PHY 0x7: 0x4DD072
[ 0.803733] PHY 0x8: 0xFFFFFFFF
[ 0.810204] PHY 0x9: 0xFFFFFFFF
[ 0.816690] PHY 0xA: 0xFFFFFFFF
[ 0.823176] PHY 0xB: 0xFFFFFFFF
[ 0.829648] PHY 0xC: 0xFFFFFFFF
[ 0.836134] PHY 0xD: 0xFFFFFFFF
[ 0.842606] PHY 0xE: 0xFFFFFFFF
[ 0.849092] PHY 0xF: 0xFFFFFFFF
[ 0.855578] PHY 0x10: 0xFFFFFFFF
[ 0.862224] PHY 0x11: 0xFFFFFFFF
[ 0.868882] PHY 0x12: 0xFFFFFFFF
[ 0.875541] PHY 0x13: 0xFFFFFFFF
[ 0.882186] PHY 0x14: 0xFFFFFFFF
[ 0.888853] PHY 0x15: 0xFFFFFFFF
[ 0.895512] PHY 0x16: 0xFFFFFFFF
[ 0.902157] PHY 0x17: 0xFFFFFFFF
[ 0.908816] PHY 0x18: 0xFFFFFFFF
[ 0.915475] PHY 0x19: 0xFFFFFFFF
[ 0.922120] PHY 0x1A: 0xFFFFFFFF
[ 0.928779] PHY 0x1B: 0xFFFFFFFF
[ 0.935438] PHY 0x1C: 0xFFFFFFFF
[ 0.942083] PHY 0x1D: 0xFFFFFFFF
[ 0.948742] PHY 0x1E: 0xFFFFFFFF
[ 0.955401] PHY 0x1F: 0xFFFFFFFF
[ 0.962019] mtk_soc_eth 10100000.ethernet eth0 (uninitialized): port 0 link up (100Mbps/Full duplex)
[ 0.980248] mtk_soc_eth 10100000.ethernet: generated random MAC address da:2e:34:ec:a7:f5
[ 0.996712] libphy: mdio: probed
[ 1.037662] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver
[ 1.050222] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5
[ 1.067213] rt2880_wdt 10000120.watchdog: Initialized
[ 1.078342] NET: Registered protocol family 10
[ 1.090121] NET: Registered protocol family 17
[ 1.099104] 8021q: 802.1Q VLAN Support v1.8
[ 1.115950] VFS: Mounted root (squashfs filesystem) readonly on device 31:3.
[ 1.131017] Freeing unused kernel memory: 176K
[ 1.139900] This architecture does not have kernel memory protection.
[ 1.849803] init: Console is alive
[ 1.856799] init: - watchdog -
[ 2.377270] random: fast init done
[ 2.939826] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[ 3.084679] usbcore: registered new interface driver usbfs
[ 3.095787] usbcore: registered new interface driver hub
[ 3.106498] usbcore: registered new device driver usb
[ 3.122211] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 3.136923] ehci-platform: EHCI generic platform driver
[ 3.157711] phy phy-usbphy.0: remote usb device wakeup disabled
[ 3.169519] phy phy-usbphy.0: UTMI 16bit 30MHz
[ 3.178403] ehci-platform 101c0000.ehci: EHCI Host Controller
[ 3.189891] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1
[ 3.205791] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000
[ 3.228165] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00
[ 3.241653] hub 1-0:1.0: USB hub found
[ 3.249524] hub 1-0:1.0: 1 port detected
[ 3.260423] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[ 3.279176] init: - preinit -
[ 4.455170] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 4.466870] 8021q: adding VLAN 0 to HW filter on device eth0
[ 4.478419] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
[ 6.365890] jffs2: notice: (338) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
[ 6.398507] mount_root: switching to jffs2 overlay
[ 6.447968] urandom-seed: Seeding with /etc/urandom.seed
[ 6.590449] procd: - early -
[ 6.596355] procd: - watchdog -
[ 6.986653] procd: - watchdog -
[ 6.993257] procd: - ubus -
[ 7.214273] procd: - init -
Please press Enter to activate this console.
[ 7.558293] kmodloader: loading kernel modules from /etc/modules.d/*
[ 7.577336] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 7.600992] usbcore: registered new interface driver cdc_wdm
[ 7.614308] Loading modules backported from Linux version wt-2017-11-01-0-gfe248fc2c180
[ 7.630338] Backport generated by backports.git v4.14-rc2-1-31-g86cf0e5d
[ 7.647936] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 7.667465] nf_conntrack version 0.5.0 (1024 buckets, 4096 max)
[ 7.741097] xt_time: kernel timezone is -0000
[ 7.910646] PPP generic driver version 2.4.2
[ 7.921862] NET: Registered protocol family 24
[ 7.933303] usbcore: registered new interface driver qmi_wwan
[ 7.974288] ieee80211 phy0: rt2x00lib_request_eeprom_file: Info - Loading EEPROM data from 'soc_wmac.eeprom'.
[ 7.994260] rt2800_wmac 10180000.wmac: Direct firmware load for soc_wmac.eeprom failed with error -2
[ 8.012497] rt2800_wmac 10180000.wmac: Falling back to user helper
[ 8.141399] firmware soc_wmac.eeprom: firmware_loading_store: map pages failed
[ 8.156079] ieee80211 phy0: rt2x00lib_request_eeprom_file: Error - Failed to request EEPROM.
[ 8.172974] rt2800_wmac: probe of 10180000.wmac failed with error -11
[ 8.217475] kmodloader: done loading kernel modules from /etc/modules.d/*
[ 11.176673] usb 1-1: new high-speed USB device number 2 using ehci-platform
[ 15.375774] 8021q: adding VLAN 0 to HW filter on device eth0
[ 15.411098] device eth0 entered promiscuous mode
[ 15.435222] br-lan: port 1(eth0.1) entered blocking state
[ 15.446077] br-lan: port 1(eth0.1) entered disabled state
[ 15.457274] device eth0.1 entered promiscuous mode
[ 15.512877] br-lan: port 1(eth0.1) entered blocking state
[ 15.523701] br-lan: port 1(eth0.1) entered forwarding state
[ 15.535013] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[ 16.405693] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 30 mar 2018, 14:28 
Offline
Administrator
Awatar użytkownika

Rejestracja: 10 kwie 2010, 00:28
Posty: 13263
Lokalizacja: Warszawa
Nie robi radia tutaj...

_________________
http://eko.one.pl - prawie wszystko o OpenWrt


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
 Tytuł: Re: dwr-960 LTE
Post: 30 mar 2018, 17:17 
Offline
Użytkownik

Rejestracja: 3 mar 2018, 09:59
Posty: 73
Reboot i radio będzie. Tak niestety działa ten skrypt.


Na górę
 Wyświetl profil  
Odpowiedz z cytatem  
Wyświetl posty nie starsze niż:  Sortuj wg  
Nowy temat Odpowiedz w temacie  [ Posty: 293 ]  Przejdź na stronę Poprzednia  1 ... 7, 8, 9, 10, 11, 12, 13 ... 15  Następna

Strefa czasowa UTC+1godz. [letni]


Kto jest online

Użytkownicy przeglądający to forum: Obecnie na forum nie ma żadnego zarejestrowanego użytkownika i 1 gość


Nie możesz tworzyć nowych tematów
Nie możesz odpowiadać w tematach
Nie możesz zmieniać swoich postów
Nie możesz usuwać swoich postów

Szukaj:
Przejdź do:  
designed by digi-led.pl
...Copyright © 2010-2013, Ekipa openrouter.info